JEI SteelBeat PRO PB10 Скачать руководство пользователя страница 28

Страница: 28 / 35

PB10 (PBE)

This document is protected by copyrights.

Copying, using, or distributing without permission of JEI Group Ltd is prohibited.

Start

the

motor

and

rotate

the

handles

the

right.

the

machining is difficult, stop

the rotation and tighten the bumper spring (

) more.

After the pipe end is machined fully, stop rotating the handles and allow several

more turns of the spindle to improve the finish of the surface.

Then, stop the

machine, separate the tool bits from

the

pipe end, release the clamping, and then

remove the machine from the pipe.

4.5.6. Adjusting the slider clearance

Use the 8 mm flat wrench to loosen the lock nuts (

, Fig. 14) and lightly

tighten

the

screws (

) with the 2.5 mm hex wrench. If, after loosening the screws (

), the slider

moves smoothly and uniformly, tighten the lock nuts (

Fig. 14.

Adjusting the slider clearance

Содержание SteelBeat PRO PB10




































Результаты поиска

Содержание SteelBeat PRO PB10

Отзывы:

Похожие инструкции для SteelBeat PRO PB10

Бренды по названию

Популярные бренды

JEI SteelBeat PRO PB10, Руководство оператора

Результаты поиска

Содержание SteelBeat PRO PB10

Отзывы:

Похожие инструкции для SteelBeat PRO PB10

Бренды по названию

Популярные бренды