JEFFES22M-110
ES 22M FESTOON LIGHT KIT
USER GUIDE
v.1.1
www.jeffersontools.com
INTRODUCTION
This Festoon lighting kit uses the latest in LED technology for long
lasting performance and features a 22M hanging light chain, complete
with 10x holders, ES bulb fittings and guards. The lights are fully
insulated, IP44 rated and suitable for both indoor and outdoor use.
FEATURES:
•
Tough, replaceable, polycarbonate 10W LED bulbs equivalent
to standard 60W GLS bulbs (100W / 8000 Lumens combined
lighting power)
•
LED bulbs provide longer lasting performance with up to 30,000
hours compared to 2,000 hours with traditional GLS 60W bulbs
•
Electrically moulded ES fittings (E27 Edison Screw)
•
IP44 rating
KIT CONTENTS:
•
10x
10W LED Light Bulbs
[A]
•
10x
Bulb wire guards
[B]
•
1x
22m of 2mm cable fitted with a BS EN 60309 Coupler and
16A plug (110V~50Hz)
[C]
SPECIFICATIONS
Supply Voltage:
110V
Frequency:
50Hz
Plug / Socket :
16A 110V BS EN 60309
Cable:
22M H05VV-F PVC 110V (2 x 2mm²)
Insulation:
IP44
Operating Temperature:
-25°C - 45°C
Illumination:
240°
Colour Temperature:
6500K
Light Emmision:
100W - 8000 Lumens
Warning:
This festoon lighting kit only operates
from a 110V~50Hz supply. Contact a qualified
electrician for advice on any issues relating to
electrical safety in your working environment prior
to use.
Information on Disposal for Users of Waste Electrical &
Electronic Equipment (WEEE)
This symbol on the product(s) and / or
accompanying documents means that used
electrical and electronic products should not be
mixed with general household waste.
For proper treatment, recovery and recycling,
please take this product(s) to designated collection
points where it will be accepted free of charge.
SAFETY GUIDELINES
Important:
Please read all information carefully
before use and keep these instructions in a safe
place for future reference.
Ensure that you check the equipment thoroughly to ensure it is safe
and fit for purpose before each use. It is important that you inspect
all plugs, sockets, power cables and electrical fittings for wear and
damage and repair or replace any defective components. Ensure that
the power cable is kept away from heat, oil and sharp edges.
The risk of electric shock can be minimised by the correct use of the
appropriate electrical safety devices. We recommend that you fit a
Residual Current Circuit Breaker (RCCB)
in the main distribution
board and that a
Residual Current Device (RCD)
is used when
operating this equipment.
The
Electricity at Work Act 1989
includes legislation that places
legal implications on employers to ensure the safety of electrical
devices in the workplace. The regulations dictate that all portable
equipment must be inspected regularly and tested to ensure that it is
safe for use. ‘Portable equipment’ means any electrical item that can
be moved and this is often referred to as
Portable Appliance Testing
(PAT)
. PAT testing should be carried out regularly on this equipment
by trained, authorised personnel, as required by the legislation.
The
Health and Safety at Work Act 1974
states that it is the
responsibility of the owner of electrical appliances to ensure that both
the equipment and working environments are maintained to ensure
safe operation at all times.
Ensure that the power supply matches voltage requirements specified
on the equipment and that the plug is wired correctly and fitted with
the correct fuse. If the electrical fuse blows, ensure it is replaced by
an identical type of fuse with the same rating.
Do not operate or connect to the electrical supply when the cable is in
a coil. Follow installation instructions prior to connecting to the sup-
ply. Disconnect from the power supply before replacing the LED bulbs
or making any adjustments to the position of the chain.
Allow the LED bulbs to cool before removing or disconnecting. Ensure
equipment is well-maintained and checked for damage before use.
Do not use if the equipment is damaged. Contact your nearest Jef-
ferson Dealer for advice on parts and repair.
INSTALLATION
1.
Prior to connecting to a power supply, secure the bulb guards to
the E27 Edison Screw Fittings, using the hooks on the guards to fix to
the cable.
2.
Carefully screw in each LED bulb, ensuring a secure fit.
3.
Hang the festoon light chain in a suitable location ensuring that
they are adequately supported and prevent straining of the cable.
The first bulb holder module should be positioned to provide
adequate cable length to the supply point and should be suitably
secured.
4.
Where possible, each bulb module should be screwed in position
using the fixing holes supplied (cable ties can be used to secure each
module if screws are impractical in your working environment).
5.
Connect the 16A plug to a 110V AC supply and turn the power
supply on.
6
. Check that all of the bulbs are functioning correctly (replace any
broken bulbs as required).
[A]
[B]
[C]
