Jeep Grand Cherokee SRT 2017 Скачать руководство пользователя | Manualshive

Страница: 465 / 589

background image

DEPARTMENT OF TRANSPORTATION UNIFORM
TIRE QUALITY GRADES

The following tire grading categories were established by
the National Highway Traffic Safety Administration. The
specific grade rating assigned by the tire’s manufacturer in
each category is shown on the sidewall of the tires on your
vehicle.

All passenger vehicle tires must conform to Federal safety
requirements in addition to these grades.

Treadwear

The Treadwear grade is a comparative rating, based on the
wear rate of the tire when tested under controlled condi-
tions on a specified government test course. For example, a
tire graded 150 would wear one and one-half times as well
on the government course as a tire graded 100. The relative
performance of tires depends upon the actual conditions of
their use, however, and may depart significantly from the
norm due to variations in driving habits, service practices,
and differences in road characteristics and climate.

Traction Grades

The Traction grades, from highest to lowest, are AA, A, B,
and C. These grades represent the tire’s ability to stop on
wet pavement, as measured under controlled conditions on

specified government test surfaces of asphalt and concrete.
A tire marked C may have poor traction performance.

WARNING!

The traction grade assigned to this tire is based on
straight-ahead braking traction tests, and does not
include acceleration, cornering, hydroplaning, or peak
traction characteristics.

Temperature Grades

The temperature grades are A (the highest), B, and C,
representing the tire’s resistance to the generation of heat
and its ability to dissipate heat, when tested under con-
trolled conditions on a specified indoor laboratory test
wheel.

Sustained high temperature can cause the material of the
tire to degenerate and reduce tire life, and excessive
temperature can lead to sudden tire failure. The grade C
corresponds to a level of performance, which all passenger
vehicle tires must meet under the Federal Motor Vehicle
Safety Standard No. 109. Grades B and A represent higher
levels of performance on the laboratory test wheel, than the
minimum required by law.

8

SERVICING AND MAINTENANCE

463

«
...
463
464
465
466
467
...
»

Содержание Grand Cherokee SRT 2017














































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grand Cherokee SRT 2017

Бренд: Daihatsu Страницы: 485

Wallbox eM4 Single

Бренд: ABL Страницы: 68

CARPOWER CAP-12XHQ

Бренд: Monacor Страницы: 5

Grand Cherokee WK2

Бренд: Jeep Страницы: 338

Бренд: Trailboss Страницы: 8

Бренд: FAAFTECH Страницы: 8

Бренд: AutoMaxi Страницы: 2

Бренд: Würth Страницы: 36

Бренд: Ranger design Страницы: 22

Quantum hardcoated N30216

Бренд: National Cycle Страницы: 3

RUDDER ANGLE INDICATOR

Бренд: VDO Страницы: 8

Бренд: Chevrolet Страницы: 372

Quantum Wash'n'Wipe N30208

Бренд: National Cycle Страницы: 12

Бренд: Saab Страницы: 37

Бренд: Brodit Страницы: 2

Бренд: Acura Страницы: 19

Бренд: Ford Страницы: 325

TOUR EASY 4 936550

Бренд: Reimo Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды