Jeep Grand Cherokee SRT 2017 Скачать руководство пользователя | Manualshive

Страница: 442 / 589

background image

Rear Axle Fluid Level Check

The rear axle oil level needs to be no lower than 1/8 in
(3 mm) below the bottom of the fill hole.

The rear axle fill and drain plugs should be tightened to 22
to 29 ft lbs (30 to 40 N·m).

CAUTION!

Do not overtighten the plugs as it could damage them
and cause them to leak.

Selection Of Lubricant

Use only the manufacturer’s recommended fluid. Refer to
“Fluids And Lubricants” in “Technical Specifications” for
further information.

Transfer Case

Fluid Level Check

For normal service, periodic fluid level checks are not
required. When the vehicle is serviced for other reasons the
exterior surfaces of the transfer case assembly should be
inspected. If oil leakage is suspected inspect the fluid level.
Refer to “Fluids And Lubricants” in “Technical Specifica-
tions” for further information.

Adding Fluid

Add fluid at the filler hole, until it runs out of the hole,
when the vehicle is in a level position.

Drain

First remove fill plug, then remove drain plug. Recom-
mended tightening torque for drain and fill plugs is 15 to
25 ft lbs (20 to 34 N·m).

CAUTION!

When installing plugs, do not overtighten. You could
damage them and cause them to leak.

Selection Of Lubricant

Use only the manufacturer’s recommended fluid. Refer to
“Fluids And Lubricants” in “Technical Specifications” for
further information.

Automatic Transmission

Selection Of Lubricant

It is important to use the proper transmission fluid to
ensure optimum transmission performance and life. Use
only the manufacturer’s specified transmission fluid. Refer
to “Fluids And Lubricants” in “Technical Specifications”

440

SERVICING AND MAINTENANCE

«
...
440
441
442
443
444
...
»

Содержание Grand Cherokee SRT 2017














































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grand Cherokee SRT 2017

Бренд: JAC Страницы: 70

Бренд: Jabra Страницы: 2

Бренд: Jabra Страницы: 38

PRIME DESIGN URX-001-E

Бренд: Safe Fleet Страницы: 8

Бренд: Vauxhall Страницы: 131

Бренд: EUFAB Страницы: 16

Parktronic system Volkswagen Golf MK7

Бренд: Car-Systems Страницы: 10

Бренд: Beper Страницы: 52

Бренд: Volvo Страницы: 123

Бренд: Mazda Страницы: 1001

Airgo Active cushion / Comfort

Бренд: TOGU Страницы: 2

Бренд: Cadillac Страницы: 78

Бренд: APS Страницы: 4

Бренд: Ford Страницы: 722

Бренд: MSD Ignition Страницы: 4

2003 Monte Carlo

Бренд: Chevrolet Страницы: 386

Бренд: Chevrolet Страницы: 410

200 CONVERTIBLE 2011

Бренд: Chrysler Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды