Jeep Grand Cherokee SRT 2017 Скачать руководство пользователя | Manualshive

Страница: 420 / 589

background image

American Petroleum Institute (API) Engine Oil
Identification Symbol

This symbol means that the oil has
been certified by the American
Petroleum

Institute

(API).

The

manufacturer

only

recommends

API Certified engine oils.

This symbol certifies 0W-20, 5W-20, 0W-30, 5W-30 and
10W-30 engine oils.

CAUTION!

Do not use chemical flushes in your engine oil as the
chemicals can damage your engine. Such damage is not
covered by the New Vehicle Limited Warranty.

Engine Oil Viscosity

Use Pennzoil Ultra 0W-40 engine or equivalent MOPAR oil
meeting the FCA Material Standard MS-12633 for use in all
operating temperatures.

The engine oil filler cap also shows the recommended
engine oil viscosity for your engine. For information on
engine oil filler cap location, refer to “Engine Compart-
ment” in this section for further information.

Synthetic Engine Oils

You may use synthetic engine oils provided the recom-
mended oil quality requirements are met, and the recom-
mended maintenance intervals for oil and filter changes are
followed.

Synthetic engine oils which do not have both the engine oil
certification mark and the correct SAE viscosity grade
number should not be used.

Materials Added To Engine Oil

The manufacturer strongly recommends against the addi-
tion of any additives (other than leak detection dyes) to the
engine oil. Engine oil is an engineered product and its
performance may be impaired by supplemental additives.

Disposing Of Used Engine Oil And Oil Filters

Care should be taken in disposing of used engine oil and
oil filters from your vehicle. Used oil and oil filters,
indiscriminately discarded, can present a problem to the

418

SERVICING AND MAINTENANCE

«
...
418
419
420
421
422
...
»

Содержание Grand Cherokee SRT 2017














































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grand Cherokee SRT 2017

Бренд: Daihatsu Страницы: 1718

ANDROID INTERFACE

Бренд: GMC Страницы: 18

Бренд: Prorack Страницы: 15

Бренд: Pyle Страницы: 4

MILSCO KIT# C746700

Бренд: K&M Страницы: 2

Бренд: Car-Interface Страницы: 25

2 Bike Carrier 977

Бренд: Thule Страницы: 6

v.LOGiC Intelligent Solution V5-NTG46

Бренд: Caraudio-Systems Страницы: 18

Бренд: Simplicity Страницы: 10

Бренд: Caraudio-Systems Страницы: 9

Бренд: TATA Motors Страницы: 151

QUICKDRAW RACHET TIE-DOWNS 855

Бренд: Thule Страницы: 3

Telescoping Computer Base C-TCB-34

Бренд: Havis-Shields Страницы: 1

Бренд: PEUGEOT Страницы: 107

Бренд: Whispbar Страницы: 14

Бренд: Setma Страницы: 13

Filtercharger 57-9004

Бренд: K&N Engineering Страницы: 4

Бренд: Honda Страницы: 219

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды