Jeep Grand Cherokee SRT 2017 Скачать руководство пользователя | Manualshive

Страница: 355 / 589

background image

3. Grab popped up outboard edge with other hand to

disengage snaps.

4. Remove the storage bin.

5. Pull the release cable to open the fuel door, push the

release cable back to the home position to re-seat the fuel
door latch to the closed position.

NOTE:

If the fuel door does not latch after the manual

release cable has been activated, the actuator latch should
be manually returned to the closed position.

VEHICLE LOADING

Certification Label

As required by National Highway Traffic Safety Adminis-
tration regulations, your vehicle has a certification label
affixed to the driver’s side door or pillar.

This label contains the month and year of manufacture,
Gross Vehicle Weight Rating (GVWR), Gross Axle Weight
Rating (GAWR) front and rear, and Vehicle Identification
Number (VIN). A Month-Day-Hour (MDH) number is
included on this label and indicates the Month, Day and
Hour of manufacture. The bar code that appears on the
bottom of the label is your VIN.

Gross Vehicle Weight Rating (GVWR)

The GVWR is the total permissible weight of your vehicle
including driver, passengers, vehicle, options and cargo.
The label also specifies maximum capacities of front and
rear axle systems (GAWR). Total load must be limited so
GVWR and front and rear GAWR are not exceeded.

Payload

The payload of a vehicle is defined as the allowable load
weight a truck can carry, including the weight of the driver,
all passengers, options and cargo.

Release Cable

6

STARTING AND OPERATING

353

«
...
353
354
355
356
357
...
»

Содержание Grand Cherokee SRT 2017














































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grand Cherokee SRT 2017

Electronic Parking Disc II

Бренд: Jacob Jensen Страницы: 28

Бренд: Fabbri Страницы: 4

Бренд: FORM FIT Страницы: 2

Edge Flush Rail

Бренд: Thule Страницы: 12

Бренд: Axxess Страницы: 8

Lippert Components LEVELEGS MPD 66385

Бренд: Atwood Страницы: 6

65 41 2 152 528

Бренд: BMW Страницы: 21

Бренд: Opel Страницы: 254

Бренд: T-Mobile Страницы: 2

Бренд: Black Horse Off Road Страницы: 7

CERTA CTCVINCVR14A

Бренд: Kogan Страницы: 4

Бренд: Peiying Страницы: 32

Бренд: Poison Spyder Страницы: 5

Бренд: Lund Страницы: 12

Бренд: Chevrolet Страницы: 46

Бренд: Blackhawk Automotive Страницы: 8

Бренд: Brodit Страницы: 2

Бренд: Buick Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды