Jeep Grand Cherokee SRT 2017 Скачать руководство пользователя | Manualshive

Страница: 252 / 589

background image

WARNING!

(Continued)

•

An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchorage position directly be-
hind the child seat to secure a child restraint top
tether strap.

•

If your vehicle is equipped with a split rear seat,
make sure the tether strap does not slip into the
opening between the seatbacks as you remove slack
in the strap.

Transporting Pets

Air Bags deploying in the front seat could harm your pet.
An unrestrained pet will be thrown about and possibly
injured, or injure a passenger during panic braking or in a
collision.

Pets should be restrained in the rear seat in pet harnesses or
pet carriers that are secured by seat belts.

SAFETY TIPS

Transporting Passengers

NEVER TRANSPORT PASSENGERS IN THE CARGO
AREA.

WARNING!

•

Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.

•

It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seriously
injured or killed.

•

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat belts.

•

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

Exhaust Gas

WARNING!

Exhaust gases can injure or kill. They contain carbon
monoxide (CO), which is colorless and odorless.
Breathing it can make you unconscious and can even-
tually poison you. To avoid breathing (CO), follow
these safety tips since vehicle equipped with a gas
engine the following applies:

(Continued)

250

SAFETY

«
...
250
251
252
253
254
...
»

Содержание Grand Cherokee SRT 2017














































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grand Cherokee SRT 2017

Бренд: Davis Instruments Страницы: 16

SP200 - QUICKSTART GUIDE 1

Бренд: Jabra Страницы: 2

BT150 - Headset - Over-the-ear

Бренд: Jabra Страницы: 2

Бренд: Subaru Страницы: 3

Бренд: BMW Страницы: 21

Бренд: Jeep Страницы: 380

Бренд: Mini Страницы: 20

Бренд: Right Weigh Страницы: 16

Бренд: Unex Страницы: 30

Бренд: Elinchrom Страницы: 101

S90 - ACCESSORY PANEL

Бренд: Volvo Страницы: 166

Бренд: WABCO Страницы: 224

T13 Outback Frontal Protection System

Бренд: T.J.M. Страницы: 18

Бренд: Audi Страницы: 4

Бренд: Mercedes-Benz Страницы: 24

Aura Mobile BT MCP-2014

Бренд: Spracht Страницы: 2

530 GRAN TURISMO - 2010

Бренд: BMW Страницы: 26

Бренд: Curt Manufacturing Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды