JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 529

Страница: 529 / 592

JD780A Series Analyzers

Using T1 Analyzer

529

Monitoring transmission

Making a test

Procedure

To select the measurement mode:

Press the

MODE

hard key.

Press the

E1/T1 Analyzer

soft key.

Select

T1 Analyzer > Monitoring

To configure measurement parameters:

Press the

MEASURE SETUP

hot key.

Press the

RX Mode

soft key, and then select the receiver input option from the following choices:

–

Terminate

: Provides 100-ohm nominal input impedance, according to the framing, line

code, and BER pattern settings.

–

Bridge

: Provides input impedance greater than one kilohm for in-service monitoring,

bridging the receiver input across lines that are terminated elsewhere in the network.

–

Monitor

: Provides 100-ohm nominal input impedance for the in-service monitoring of T1

lines.

Toggle the

Framing

soft key between

SF-D4

and

ESF

and select the framing type for your

receiver setting:

–

SF-D4 (Super Frame-D4):

Group of 12 frames, used to align equipment for framing.

–

ESF (Extended Super Frame):

Group of 24 frames, used to align equipment for framing.

4K for a maintenance channel (Facilities Data Link), 2K for CRC-6 checksum, and 2K for
framing/synchronization.

NOTE

If the framing type does not match with your receiver setting, a framing alarm occurs.

Toggle the

Line Code

soft key between

AMI

and

B8ZS

and select the line code type to send an

T1 signal:

–

AMI:

It stands for Alternate Mark Inversion. A line code uses one three level signal to

convey binary digits in which successive binary ones (

“marks” or pulses) are of alternating

polarity, either positive or negative, equal in amplitude. A binary zero

(“space”) is

transmitted as no pulse or zero amplitude.

–

B8ZS:

It stands for Bipolar with 8-Zero Substitution. A coding scheme in which the

transmitter "substitutes" a fixed pattern of ones, zeros, and BPVs in place of 8 consecutive
zeros.

To start or stop monitoring:

Press the

MEASURE

hot key.

Press the

Monitoring

soft key, and then select the monitoring option as needed:

Start

Stop

, or

Clear

Optional

. You can save event records automatically by using the

Save Logging Data

soft key. See

“Using save” on page 31 for more information.

Содержание CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CellAdvisor JD780A Series

Отзывы:

Бренды по названию

Популярные бренды

JDS Uniphase CellAdvisor JD780A Series, Руководство пользователя

Результаты поиска

Содержание CellAdvisor JD780A Series

Отзывы:

Бренды по названию

Популярные бренды