JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 444

Страница: 444 / 592

JD780A Series Analyzers

444

Using TD-SCDMA Signal Analyzer

Procedure

Toggle the

Display

soft key and select the display option:

–

Result

to view the result table.

The Display Result menu becomes activated.

–

Settings

to view the measurement settings for the auto measurement.

Toggle the

Display Result

soft key and select the display result option:

–

Full

: to view detailed measurement readings with the pass/fail indication.

–

Quick

: to view only the Pass/Fail results.

To view the measurement results for a different carrier, press the

View Carrier

soft key and then

select the carrier number to view.

Conducting TD-SCDMA OTA measurements

Sync-DL ID scanner

Setting measure setup

After configuring test parameters as described in the

“Configuring test parameters” on page 415, you

can continue your measurement.

Procedure

Press the

MEASURE SETUP

hot key.

Toggle the

Sync-DL ID

soft key and select

Auto

Manual

to set the Sync Downlink ID

automatically or manually.

Optional

. To select the delay, complete the following steps:

Press the

Miscellaneous

soft key.

Press the

Delay

soft key to set the amount of delay in µs.

Enter a value by using the numeric keys. You can also use the rotary knob.

Press the

µs

soft key.

NOTE

The Delay setting is used only when there is a time offset in the signals to be measured.

Optional

. Go to

SAVE/LOAD

> Save

, and then select the save option from the choices available

for your measurement mode. See

“Using save” on page 31 for more information.

Содержание CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CellAdvisor JD780A Series

Отзывы:

Бренды по названию

Популярные бренды

JDS Uniphase CellAdvisor JD780A Series, Руководство пользователя

Результаты поиска

Содержание CellAdvisor JD780A Series

Отзывы:

Бренды по названию

Популярные бренды