JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 433

Страница: 433 / 592

JD780A Series Analyzers

Using TD-SCDMA Signal Analyzer

433

Optional

. Press the

Miscellaneous

soft key, and then do the following(s) as needed:

–

To select how to determine scrambling estimation, toggle the

Scramble

soft key and select

Spec

Full

NOTE

The Spec searches

“Sync Sequence Number” from 0 to 31 based on the TD-SCDMA

specification and determines

“Scrambling Code Number” by using the sync sequence

number, while the Full does from 0 to 127 fully.

–

To select how to determine the Midamble spread factor estimation either in full or maximum
power search, toggle the

Mid SF Map

soft key and select

Max

Spec

NOTE

The Max determines the spread factor of the Midamble by using the maximum power of
the received Midamble, while the Spec searches

“Default Midamble Allocation” based on

the TD-SCDMA specification.

–

To select the detect mode, press the

Detect Mode

soft key and then select the option:

Auto

QPSK/8PSK

QPSK

8PSK

16 QAM

, or

64 QAM

Measurement example

Figure 214

Power vs. time (mask) measurement with TD-SCDMA signal analyzer

NOTE

You can use the

LIMIT

hot key to analyze your measurements with the user-definable

limit and Pass/Fail indication. See

“Setting limit for power vs. time tests” on page 435 for

more information. The DwPTS Power and UpPTS Power are not used in the power vs.
time (mask) tests.

Timogram

Setting measure setup

After configuring test parameters as described in the

“Configuring test parameters” on page 415, you

can continue your measurement. The measurement settings can be saved and recalled as a file.

Procedure

Содержание CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CellAdvisor JD780A Series

Отзывы:

Бренды по названию

Популярные бренды

JDS Uniphase CellAdvisor JD780A Series, Руководство пользователя

Результаты поиска

Содержание CellAdvisor JD780A Series

Отзывы:

Бренды по названию

Популярные бренды