JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 172 | Manualshive

Страница: 172 / 592

JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 172

JD780A Series Analyzers

172

Using WCDMA/HSPA+ Signal Analyzer

NOTE

You can use the

LIMIT

hot key to analyze your measurements with the user-definable

limit and Pass/Fail indication. See

“Setting limit for modulation tests” on page 180 for

more information.

Setting display

You can view .your measurement results in a different view option.

Procedure

1.

Press the

TRACE/DISPLAY

hard key.

2.

Toggle the

View

soft key and select the display option:

–

Zoom

:

to view the result in detail with zoom-in window.

The Position and Width menus become activated.

–

Full

:

to view the full measurement result.

3.

To define the zoom start position and width, complete the following steps:

a.

Press the

Position

soft key.

b.

Enter a value of the position by using the numeric keys.

c.

Press the

Enter

soft key.

d.

Press the

Width

soft key, and then select the Walsh code option:

32

,

64

,

128

, or

256

.

4.

Toggle the

Constellation

soft key between

On

and

Off

to enable or disable the constellation

chart on the Code Domain Power screen.

5.

Toggle the

Control Channel

soft key and select the control channel mode option:

–

Normal

:

to view the relative ratio of each control channel vs. total power.

–

Delta

:

to view the relative ratio of each control channel vs. CPICH channel.

Relative code domain power

The Relative Code Domain Error (RCDE) measurement provides relative code domain error analysis
that is particularly required by HSPA+.

Setting measure setup

After configuring test parameters as described in the

“Configuring test parameters” on page 155, you

can continue your measurement. The measurement settings can be saved and recalled as a file. You
can also use JDViewer, PC application software to configure a measure setup, save as a file, and load
the file on to the instrument.

Procedure

1.

Press the

MEASURE SETUP

hot key.

2.

Optional

. To set the scramble code, complete the following steps:

a.

Toggle the

Scramble

soft key between

Auto

and

Manual

.

b.

Enter a value by using the numeric keys to set manually.

c.

Press the

Enter

soft key.

3.

Optional

. Press the

Detect Mode

soft key, and then select the signal standard option:

WCDMA

,

HSDPA

, or

HSPA+

. HSDPA is set by default.

«
...
170
171
172
173
174
...
»

Содержание CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды