JD FC-P30-UL, Руководство оператора

Страница: 4 / 8

OPERATOR’S MANUAL FC-P30-UL
4.
OPERATOR’S MANUAL FC-P30-UL
5.
OPERATION
STORAGE
1. Always place the valve in the “OFF” position when not in
use.
2. Wrap and store the hose on the provided hose wrap brack-
et.
3. Wrap and store the ground wire on the provided wire wrap
bracket.
4. Locate the park the Gas Caddy on a flat level surface, away
from any potential ignition sources, away from any potential
hazards that may impact or damage the Gas Caddy.
5. Lock the wheel brakes.
6. Be certain that the fuel gage vent dome, indicator cap, fill
tube and fill tube cap are all present and secure. Replace
any missing parts immediately.
7. Do not turn the pump handle when not in use as this may
accidentally dispense fuel.
Fig. 2 Fig. 3
PRODUCT SPECIFICATIONS
REPLACEMENT FILTERS
Weight (empty): 154 lbs (69.5 kg)
Capacity: 30 gal (114 L)
Length: 31.25” (88.9 cm)
Width: 25.00” (63.5 cm)
Height: 46.00” (117.0 cm)
Approx. Flow: 5 gpm (19 L pm) @ 110 Rev/min
Fuel Type Filter Type Part No.
Unleaded Gasoline 10 micron 10M-FF
Diesel/Kerosene 30 micron 30M-FF
E85 Ethanol 1 micron 1M-FF
Note: Coat the O-ring seal with oil or grease before assembly. Hand tighten by
turning approximately 1/2 turn after rubber seal contacts the filter support. Do
not over-tighten.
REPLACEMENT PARTS:
Item Description Qty Part No.
1 Tank 1 _____
2 Handle 1 30GC-02C
3 Cover 1 30GC-49-UL
4 Wheel (10”) 2 30GC-06-UL
5 Caster (5”) 2 30GC-48
6 Fuel Gage (cap/nut) 1 30GC-FGK
7 Fuel Gage (complete) 1 FC-P30-FG
8 Vent 1 30GC-08-VENT
9 Fill Tube 1 30GC-09-01
10 Fill Cap 1 30GC-09-02
11 Hose Assembly 1 80-593-NI
12 Ground Strap 1 80-572
13 Valve/Filter Support Asm. 1 30GC-30/31
14 Manifold 1 30GC-22A
15 Hose Kit (3 Hoses) 1 FC-P30-HK
16 Rotary Pump 1 JDI-35-UL
17 Contents Decal Set 1 FC-CON
18 Hose Bracket 1 30GC-46
19 Ground Wire Bracket 1 30GC-47
PUMPING FROM GAS CADDY TO VEHICLE
1. Position the Gas Caddy near the vehicle and lock the front
casters brakes.
2. Attach the ground wire clamp to the vehicle to a known
ground surface.
3. Place the hose inside the fill pipe of the vehicle fuel tank.
4. Align valve handle so that the point is position to the “OUT”
to vehicle position. (See Fig. 3)
5. Turn pump in direction shown on the pump. Turn briskly until
pump primes and fluid is visibility flowing in the hose.
6. Continue to turn the pump handle to maintain flow to the
vehicle.
7. Stop turning the handle when the desired amount has been
pumped.
8. Turn the valve to the “IN” to tank position.
9. Uncoil and raise the hose and turn the handle 4-8 turns to
return any remaining fuel in the system to the tank.
10. Coil and hang the hose on the hanger bracket.
11. Turn valve to the “OFF” position.
16
14
18
10
9
7
6
8
13
2
1
19
12
4
5
3
11
15 17
Not Shown
Replacement Parts & Accessories
PUMPING FROM VEHICLE TO GAS CADDY
1. Position the Gas Caddy near the vehicle and lock the front
casters brakes.
2. Attach the ground wire clamp to the vehicle to a known
ground surface.
3. Place the hose inside the fill pipe of the vehicle fuel tank.
4. Align valve handle so that the point is to the “IN” to tank
position. See figure 2.
5. Turn pump in the direction shown on the pump. Turn briskly
until pump primes and fluid is visibly flowing in the hose.
6. Continue to turn the pump handle to maintain flow to the Gas
Caddy.
7. Stop turning the handle when the desired amount has been
pumped.
8.Uncoil and raise the hose and turn the handle 4-8 turns to
return any remaining fuel in the system to the tank.
9.Coil and hang the hose on the hanger bracket.
10. Turn valve to the “OFF” position.