background image

© 2019 JCM Global Corporation

5

Part No. 960-000207R_Rev. A

TBV™-100/101 Units

Table 3 

DS1/DS3 - Denomination INHIBIT/ACCEPT Switches

                                                                                                                                    

  DS1/DS3

*

* Refer to the Software Information Sheet for the downloaded Firmware for DS1 or DS3 Settings.

Switch 

No.

Switch ON

Switch OFF

1

VEND 1 INHIBIT

VEND 1 ACCEPT

2

VEND 2 INHIBIT

VEND 2 ACCEPT

3

VEND 3 INHIBIT

VEND 3 ACCEPT

4

VEND 4 INHIBIT

VEND 4 ACCEPT

5

VEND 5 INHIBIT

VEND 5 ACCEPT

6

VEND 6 INHIBIT

VEND 6 ACCEPT

7

VEND 7 INHIBIT

VEND 7 ACCEPT

8

N/A

† N/A = Not Applicable (Never switched to ON position).

OFF (Fixed)

Table 4 

DS2 - BNF Buzzer/Volume Switch

                                                                                                                                    

  DS2

Switch 

No.

Switch ON

Switch OFF

1

N/A

OFF (Fixed)

2

Performance Buzzer ON

Performance Buzzer OFF

3

ON (Fixed)

N/A

4

N/A

*

* N/A = Not Applicable (never switched to ON position).

OFF (Fixed)

 ON

OFF

  ON

 OFF

Содержание TBV-100 FSH



























Отзывы:

Похожие инструкции для TBV-100 FSH