manualshive.com logo in svg

jcb JS130, Руководство по обслуживанию

Поделиться
Скачать
jcb JS130 Скачать руководство пользователя страница 275

30 - 1

Introduction

The control valve is located on the mainframe to the rear of the boom mounting. Its function is to direct pressurised oil by
means of the operator’s controls to the rams and motors which supply power for the machine’s operation.

The valve is designed to perform the following functions:

a

Controlling oil flow direction.

b

Operating the hydraulic system smoothly, accurately and safely.

c

Maintaining the hydraulic circuit pressure within specified ranges.

Integrated control valves operate a tandem circuit to provide maximum pressure when simultaneous operations are required.
Check valves are incorporated to provide load hold functions.

Identification of spool functions, as marked on the valve body, is as follows:

TL

=

Left hand track motor

TR

=

Right hand track motor

AM

=

Dipper ram

OPT

=

Auxiliary supply to attachment (if fitted)

SW

=

Slew motor supply

BKT

=

Bucket ram

BM

=

Boom rams

Technical Data

Rated flow

120 l/min (26.4 gal/min)

Maximum pressure for normal use

350 kgf/cm

2

(4978 lbf/in

2

)

Oil temperature range

- 20 ~ 90 °C (-4.4 ~ 194 °F)

Maximum oil temperature

100 °C (212 °F)

Pilot maximum allowable pressure

40 kgf/cm

2

(569 lbf/in

2

)

Pilot operation pressure

2.8 ~ 24 kgf/cm

2

(40 ~ 341 lbf/in

2

)

Spool stroke

8 mm (0.315 in)

Control method

Hydraulic pilot operation

Main relief valve

2-step pressure switching type relief valve

Standard pressure setting

320 kgf/cm

2

(4550 lbf/in

2

) @ 91 l/min (20.02 gal/min)

Maximum pressure setting

350 kgf/cm

2

(4977 lbf/in

2

) @ 83 l/min (18.26 gal/min)

Overload relief valve

Pilot operated type relief valve plus make-up valve

Standard pressure setting (boom raise, dipper, bucket)

365 kgf/cm

2

(5190 lbf/in

2

) @ 30 l/min (6.6 gal/min)

Maximum pressure setting (boom lower)

300 kgf/cm

2

(4266 lbf/in

2

) @ 30 l/min (6.6 gal/min)

Spool

Solid type

Weight

104 kg (229.3 lb)

Function

Travel priority, slew priority, boom/dipper with load holding, 
bucket, auxiliary

Section E

Hydraulics

9803/6410

Section E

30 - 1

Issue 1

Control Valve

Содержание JS130






















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды