manualshive.com logo in svg

jcb JS130, Руководство по обслуживанию

Поделиться
Скачать
jcb JS130 Скачать руководство пользователя страница 21

7 - 1

Section 1

General Information

9803/6410

Section 1

7 - 1

Issue 1

Sealing and Retaining Compounds

JCB Multi-Gasket

A medium strength sealant suitable for all sizes of gasket
flanges, and for hydraulic fittings 25-65 mm diameter.

4102/1212

JCB High Strength Threadlocker

A high strength locking fluid for use with threaded
components.

4102/0551

JCB Retainer (High Strength)

For retaining parts which are unlikely to be dismantled.

4101/0651

JCB Threadlocker and Sealer

A medium strength locking fluid for sealing and retaining
nuts, bolts, and screws up to 50 mm diameter, and for

hydraulic fittings up to 25 mm diameter.

4101/0251

JCB Threadlocker

A locking fluid for use on threads larger than 50 mm
diameter.

4101/0451

50ml

JCB Threadlocker and Sealer

A medium to high strength locking fluid for retention

(High Strength)

and sealing of ram piston heads.

4101/0552

JCB Activator 

A cleaning primer which speeds the curing rate of 

4104/0251

Aerosol

anaerobic products.

4104/0253

Bottle

JCB Cleaner/Degreaser

For degreasing components prior to use of anaerobic 

4104/1557

Aerosol

adhesives and sealants.

Anti-Seize Paste

A compound used for assembly and prevention of parts 
seizure.

4003/0211

Direct Glazing Kit

For one pane of glass; comprises items marked 

†

below 

plus applicator nozzle etc.

† Ultra Fast Adhesive

For direct glazing

4103/2109

310 ml

† Active Wipe 205

For direct glazing

4104/1203

250 g

† Black Primer 206J

For direct glazing

4201/4906

30 ml

Clear Silicone Sealant

To seal butt jointed glass. 

4102/0901

The part numbers and descriptions of sealing and retaining compounds available from JCB Service have been revised with
effect from January 1997 (see MI 563/H, 507/HA, 511/E). 

References to these products on subsequent pages in this service manual will be progressively updated, but for convenience a
cross reference table is shown below.

Old Description

Old Part Number

New Description

New Part Number

JCB High Strength Threadlocker

4102/0502

JCB High Strength Threadlocker

4102/0551

JCB High Strength Retainer

4101/0602

JCB Retainer (High Strength)

4101/0651

JCB Lock & Seal

4101/0202

JCB Threadlocker & Sealer

4101/0251

Loctite 243

4101/1101

Use 4101/0251

JCB Multi-Gasket

4102/1204

JCB Multi-Gasket

4102/1212

High Strength Lock and Seal

4104/0502

JCB Threadlocker & Sealer (High Strength)

4101/0552

JCB Threadlocker

4101/0402

JCB Threadlocker

4102/0451

Loctite Activator N

4104/0101 Aerosol

JCB Activator

4104/0251

4104/0102 Bottle

4104/0253

Super Clean Safety Solvent

4104/0601 Aerosol

No longer available, Replaced by

4104/1557

JCB Cleaner & Degreaser

4104/1538 Aerosol

JCB Cleaner/Degreaser

4104/1557

Note: 

High Strength Threadlocker was previously called High Strength Gasketing (4102/0502). 

Содержание JS130






















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды