ENGLISH
USER
MANUAL
JB SYSTEMS
®
7/53
TWINBEAM
COLOR
Laser
DMX-CONFIGURATION OF TWINBEAM LASER:
CHANNEL VALUE DESCRIPTION
1
000-200
Stepper motor scanning speed (from fast to slow)
201-254
Twinbeam laser is switched to stand-alone mode (use the AUTO/MUSIC switch
to put the laser in the desired mode)
255
Complete reset (to be used while switching from stand-alone to DMX mode)
2
000-014 Pattern
1
015-020 Pattern
2
023-027 Pattern
3
028-034 Pattern
4
035-041 Pattern
5
042-048 Pattern
6
049-055 Pattern
7
056-062 Pattern
8
063-070 Pattern
9
071-076 Pattern
10
077-083 Pattern
11
084-090 Pattern
12
091-097 Pattern
13
098-104 Pattern
14
105-111 Pattern
15
112-118 Pattern
16
119-125 Pattern
17
126-132 Pattern
18
133-140 Pattern
19
141-153 Pattern
20
154-160 Pattern
21
161-167 Pattern
22
168-174 Pattern
23
175-181 Pattern
24
182-188 Pattern
25
189-195 Pattern
26
196-202 Pattern
27
203-210 Pattern
28
211-216 Pattern
29
217-223 Pattern
30
224-230 Pattern
31
231-251 Pattern
32
252-255 Pattern
33
3
000-255
Rotation of the patterns
4
000-255
Zooming: pattern size (from small to big)
5
000-255 Panning
movement
(X-axis:
left to right - value 128 is middle position)
6
000-255
Tilt movement (Y-axis: up and down - value 128 is middle position)
7
000
Blackout (works also in DMX standalone mode)
001-254
Blanking frequency (from low to high)
255
No
blanking
8
000-027
Original colors of the pre-programmed patterns
028-055
Beam1 = Off
Beam2 = Red
056-083
Beam1 = Green
Beam2 = Green
084-111
Beam1 = Green
Beam2 = Yellow
112-139
Beam1 = Green
Beam2 = Red + Green
140-167
Beam1 = Green
Beam2 = Green
168-195
Beam1 = Green
Beam2 = Red
196-254
Beam1 = Green
Beam2 = Red + Green
255
Random
color
ENGLISH
USER
MANUAL
JB SYSTEMS
®
8/53
TWINBEAM
COLOR
Laser
MAINTENANCE
•
Make sure the area below the installation place is free from unwanted persons during
servicing.
•
Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
•
All screws used for installing the device and any of its parts should be tightly fastened
and may not be corroded.
•
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally
free from any deformation.
•
When an optical lens is visibly damaged due to cracks or deep scratches, it must be
replaced.
•
The mains cables must be in impeccable condition and should be replaced immediately
when even a small problem is detected.
•
In order to protect the device from overheat the cooling fans (if any) and ventilation
openings should be cleaned monthly.
•
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
•
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surroundings can cause
greater accumulation of dirt on the unit’s optics.
•
Clean with a soft cloth using normal glass cleaning products.
•
Always dry the parts carefully.
•
Clean the external optics at least once every 30 days.
•
Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified
personnel!
SPECIFICATIONS
Mains Input:
AC 230V, 50Hz
Fuse:
250V 1.5A slow blow (20mm glass)
Sound Control:
Internal microphone
DMX connections:
3pin XLR male / female
DMX channels:
8 channels
DMX starting address:
001
Æ
255
Laser Power:
100mW Green CW laser (
λ
= 532nm)
80mW Red CW laser (
λ
= 650nm)
Laser radiation class:
3B
Laser Safety Standard:
EN60825-1:1994 + A1:2002 + A2:2002
Size:
26 x 30x 10cm
Weight:
5,8kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
