Direct Thermal Print USB POS Receipt Printer Model 4230
Installation Instructions
JAY Direct Thermal Print POS Receipt Printer Model 4230 works with POS PC Terminals with a USB I/O Port
JAY Printer Driver Software v1.1 supports Microsoft Windows Operating Systems: XP SP3 32bit; Vista SP2 32/64bit; 7 SP1 32/64bit; 8 32/64bit; 8.1 32/64bit
Features
2¼"/58.mm Paper Roll
100mm Print Speed
12VDC RJ11 Cash Drawer Jack
USB POS Terminal I/O
In Box with Printer
USB Interface Cable
Power Supply Adapter
Power Supply Adapter Power Cord
Starter Paper Roll.
No CD is included. Download software from Company Web Site. See “Install Printer Driver Software ...” below
Setup Procedures - Tasks must be performed in sequencial order as follows:
Install Thermal Paper Roll into Printer:
1.
Open printer cover
2.
Place paper roll in printer with cut edge down facing forward.
3.
Pull-out some paper.
4.
Close cover. Press down. Avoid error position of paper roll.
Connect the Printer to the POS Terminal:
1.
Make sure printer power is OFF.
2.
Connect applicable IFC to the USB I/O connector port in back of the printer.
3.
Connect other end of the IFC to a USB connector port on POS terminal.
Prepare Cash Drawer for Operation (if user’s cash drawer is used):
1.
Open cash drawer by turning front drawer lock to the left.
2.
Remove the hold-down tape from installed cash tray &/or coin till.
3.
Make sure that cash tray &/or coin till are seated flat in the drawer.
4.
Connect cash drawer to the POS Receipt Printer.
Perform Printer Self-checking Function:
1.
Connect the Power Supply Adapter to the POS Printer:
a.
Connect the Power Supply Adapter Cord to an AC wall outlet.
b.
Connect the Power Supply Adapter Cord to the Power Supply Adapter.
c.
Connect the Power Supply Adapter Cord to the Printer.
2.
Make sure printer POWER SWITCH is in OFF position.
3.
Press FEED button & hold down.
4.
While FEED button is pressed & held down turn POWER SWITCH to ON.
5.
The Self-Check List prints.
Install Printer Driver Software v1.1 onto POS Terminal:
1.
Download the Printer Driver Software v1.1 from the Company web site: www.jaysystems.com.
a.
Click on Products.
b.
Click on Printers.
c.
Scroll to bottom of listing & find “JAY Printer Driver Software v1.1".
d.
Scroll to “Series 6200 80mm Printers (Models 6210 & 6220).
e.
Click the title “Series 6200 80mm Printers” to down load software. Menu is displayed.
2.
Click on Install Driver:
a.
Wait for installation to complete.
b.
Close separate window.
3.
Click on USB Interface:
a.
Drop-down menu appears.
b.
Select USB Interface.
c.
If USB Interface cannot be selected see NOTE 1 under “Trouble Shooting”.
4.
Click on USB I/O Port #:
a.
USB I/O Port # Drop-down Menu appears.
b.
Select USB port from drop-down menu
i.
USB port is usually lowest # in menu.
ii.
If a USB I/O is not available perform USB I/O maintenance or see Installation Support under Trouble Shooting.
iii.
Switching USB ports or using USB hubs will change port #.
Perform Test Operation:
1.
Press Test:
a.
Printer prints “Testing” on receipt.
b.
Cash drawer opens (if one is installed with system).
2.
If cash drawer does not open:
a.
Check connections.
b.
Redo Setup Procedures.
3.
If drawer continues to not open see NOTE 2 under “Trouble Shooting”.
End of Setup Procedures
Printer Model 4230
Power Cord.
USB Interface Cable
Paper Roll
Power Supply Adapter
Install Paper Roll
Power Switch
Control Panel
USB I/O, Cash Drawer I/O, Power Cord
Copyright © 2015 by JRS-All Rights Reserved / www.jaysystems.com
Page 1 of 2
JAY Direct Print POS Receipt Printer Model 4230 Manual-March 31, 2015
