Jay-Lor 5750HD Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 81

background image

AAA-055-00187

31

5000 SERIES HD TRAILER OWNER MANUAL

Corner Door Discharge

Figure 18 - Front Right Corner Door

The corner discharge door is controlled hydraulically from the tractor. When the door is opened, feed
will discharge from the machine onto the ground.

The door can be raised up to a maximum of 28 inches (71 cm) in height. The corner door can be
located in the rear left or the front right corner of the machine. The optional chute assembly can be
removed for transporting or storage purposes.

Centre Side (C-Side) Door Discharge

Figure 19 - Dual Right Centre Side Doors

The centre side discharge door is controlled hydraulically from the tractor. When the door is opened,
feed will discharge from the machine onto the ground.

The doors can be raised up to a maximum of 28 inches (71 cm) in height. Centre side doors can be
located on the left and/or right side of the machine. The optional chute assembly can be removed for
transporting or storage purposes.

«
...
30
31
32
33
34
...
»

Содержание 5750HD


















































































Отзывы:

Нет отзывов

Похожие инструкции для 5750HD

Бренд: C.M.O Страницы: 10

Бренд: Raymarine Страницы: 90

Бренд: B-K lighting Страницы: 3

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Datex-Ohmeda Страницы: 80

Бренд: MacDon Страницы: 2

Бренд: V-TAC Страницы: 6

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

Бренд: ParaBody Страницы: 5

Бренд: M-system Страницы: 2

Бренд: Rico Страницы: 34

Бренд: Yardline Страницы: 75

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды