Javad TRIUMPH-1M, Руководство пользователя

Страница: 12 / 27

12 www.javad.com
• The LED color indicates the battery status:
• Green - greater than 85% charge.
• Yellow - an intermediate charge.
• Red - less than 15% charge.
Blinking every 1 sec according to the battery means
receiver is ON without external power. LED solid ac-
cording to the battery means external power is con-
nected.
The BT (Bluetooth) LED indicates the level of activ-
ity at the Bluetooth® wireless technology communi-
cation link:
• Blue – the Bluetooth® module is on and a con-
nection has been established.
• Yellow – the Bluetooth® module is on and a con-
nection is establishing.
• Red – connection is not established.
• No light – the Bluetooth® module is not active.
The WLAN LED displays the status of the WiFi con-
nection.
• Green – WLAN module is connected to access
point or adhoc mode is initialized correctly.
• Yellow – WLAN module is on and in process of ini-
tialization.
• Red – WLAN module error.
• No light – WLAN is not active.
The SAT (satellites) LED displays the number of
tracked satellites.
• Green – eight and more satellites.
• Yellow – five to seven satellites.
• Red – less than five satellites.
• No light – no satellites.
Effective number of satellites are total number of
satellites tracked minus the number of non-GPS sys-
tems tracked. E.g. if 8 GPS and 5 GLONASS are tracked
the effective number of satellites is 12.
The POS (position) LED indicates position solution
for current surveying mode:
• Green – Fixed/Diff position solution is obtained.
• Yellow – Float/No-Diff position solution is ob-
tained.
• Red – No position.
• No light - no satellites.
The REC (record) LED displays the data recording
status and blinks on each recording.
• Green – recording data.
• Yellow – less than 10 min memory left.
• Red – memory is full.
• No light - not active.
The On/Off (power) button turns the receiver on
and off. The Record button starts/stops data record-
ing.
TURNING ON/OFF
To turn ON the receiver, press and hold the pow-
er button until the LEDs briefly flash. To turn OFF the
receiver, press and hold the power key for more than
one and less than four seconds (until both the SAT
and the REC LEDs are off).
CHARGING THE BATTERIES
Warning:
Risk of explosion if battery is replaced by an incor-
rect type. Dispose of used battery according to the instructions.
Warning:
Before beginning to work, fully charge the batteries
for maximum operating time. An approximately 6-hour charge cy-
cle will fully charge the batteries; the batteries will charge simulta-
neously. The batteries can not be overcharged.
CAUTION:
RISK OF EXPLOSION IF BATTERY IS RE-
PLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS
Warning:
The Li-Ion batteries used in the battery packs should
run at no less than 80% capacity after 500 charging cycles. These
batteries do not need to be drained before recharging.
Warning:
Never attempt to open the casing of the detachable
batteries! Lithium-Ion batteries can be dangerous if mishandled!
Warning:
Warning:
Do not incinerate or heat battery pack above 212 de-
grees Fahrenheit (100 degrees Celsius). Excessive heat can cause
serious damage and possible explosion.
Warning:
The batteries (or batteries installed) shall not be ex-
posed to excessive heat such as sunshine, fire or the like.
Warning:
Do not attempt to open the battery pack.
Warning:
Do not disassemble the battery pack.
Warning:
Do not charge in conditions different than specified.
Warning:
Do not use other than the specified battery charger.
Warning:
Do not short circuit the battery pack.
Warning:
Do not crush or modify the battery pack.
POWER SUPPLY
REQUIREMENTS
The socket-outlet shall be installed near the equip-
ment and shall be easily accessible.
A single external power supply with 5 pin ODU
connector or SAE connector is necessary to operate