Jasic EVO 2.0 EM-160C Скачать руководство пользователя

Страница: 73 / 82

TROUBLESHOOTING

ERROR CODES

The following operation requires sufficient professional knowledge on electric aspects and

comprehensive safety knowledge. Make sure the input cable of the machine is disconnected

from the electricity supply and wait for 5 minutes before removing any machine covers.

The control display is also used for providing error messages to the user, if an error message is displayed,
the power source may only function to a limited capacity and the cause of the error should be checked
as soon as possible.

The below is a list of error codes for the Jasic EVO EM

160 and EM

200 welding machines.

Error
Code

Error Code

Description

Possible Cause

Check

E10

Overcurrent

protection

The output is at

maximum capacity

current of machine

Turn the machine off and back on again.

If overcurrent protection alarm is still active, contact

your suppliers approved technician.

E31

Undervoltage

protection

The input mains

voltage is too low

Turn the machine off and back on again.

If the alarm continues, check the input voltage.

If the input voltage is within specification and the

alarm persists, contact your suppliers approved

technician.

E32

Overvoltage

protection

The input mains

voltage is too high

Turn the machine off and back on again.

If the alarm continues, check the input voltage.

If the input voltage is within specification and the

alarm persists, contact your suppliers approved

technician.

E34

Undervoltage

protection

Under voltage in

inverter circuit

Turn the machine off and back on again.

If the alarm continues, check the input voltage.

If the input voltage is within specification and the

alarm persists, contact your suppliers approved

technician.

E60

Overheating

An over temperature

signal received from

the output rectifier

circuit

Do not turn off the machine, wait for a while and

after the thermal error goes off then you can

continue welding.

While error code is ON, machine cannot cut.

Ensure cooling fans are operational.

Decrease duty cycle welding activity.

E61

Overheating

An over temperature

signal received from

the Inverter IGBT

circuit

Do not turn off the machine, wait for a while and

after the thermal error goes off then you can

continue welding.

While error code is ON, machine cannot cut.

Ensure cooling fans are operational.

Decrease duty cycle welding activity.

Abnormal VRD

VRD voltage is too

high or too low

Turn the machine off and back on again.

If the fault VRD alarm persists, contact your suppliers

approved technician.

Содержание EVO 2.0 EM-160C



















































































Результаты поиска

Содержание EVO 2.0 EM-160C

Отзывы:

Похожие инструкции для EVO 2.0 EM-160C

Бренды по названию

Популярные бренды

Jasic EVO 2.0 EM-160C, Руководство оператора

Результаты поиска

Содержание EVO 2.0 EM-160C

Отзывы:

Похожие инструкции для EVO 2.0 EM-160C

Бренды по названию

Популярные бренды