Jandy APUREM Скачать руководство пользователя

Страница: 1 / 52

Jandy

AquaPure

Electronic

Salt Water Chlorinator

And

INSTALLATION AND

OPERATION MANUAL

PureLink™

Water Purification System

Power Center and Cell Kit

Models:

APUREM
PLC700
PLC1400

H0325600 Rev F

ENGLISH

WARNING

If these instructions are not followed exactly, a fire or explosion may

result, causing property damage, personal injury, or death.

FOR YOUR SAFETY:

This product must be installed and serviced by a contractor who is licensed and qualified

in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements

exists. In the event no such state or local requirement exists, the installer or maintainer must be a professional with

sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual

can be followed exactly. Before installing this product, read and follow all warning notices and instructions that

accompany this product. Failure to follow warning notices and instructions may result in property damage, personal

injury, or death. Improper installation and/or operation will void the warranty.

Содержание APUREM





















































Результаты поиска

Содержание APUREM

Отзывы:

Похожие инструкции для APUREM

Бренды по названию

Популярные бренды

Jandy APUREM, Инструкция по установке и эксплуатации

Результаты поиска

Содержание APUREM

Отзывы:

Похожие инструкции для APUREM

Бренды по названию

Популярные бренды