13
4.10 2012+ CLEARRAY Facts
Our water purification system will begin disinfecting your water instantly. CLEAR
RAY
Water Purification System
is exclusive technology utilizing natural ultraviolet technology to sanitize your water, disinfecting bacteria,
viruses, and algae in portable hot tubs. The ultraviolet light otherwise known as UV-C or germicidal light inacti-
vates the microorganisms by disrupting the DNA so that it cannot reproduce and is considered lifeless. The bal-
last is the power supply for the purification system; it has two LED indicator lights the green indicating incoming
power flow and the red indicating the system is properly working. CLEAR
RAY
is standard for all models.
Note:
• For JLX/2011-2013 J300 Models:
The CLEAR
RAY
System only runs when the circulation pump is running
and shuts off when either jets pump is manually activated during spa use. The system will remain off for 5
minutes after both jets pumps time out or are manually turned off, then resume operations if the circulation
pump is programmed to run.
• For J200 Models:
The CLEAR
RAY
System only runs when the jets pump 1 is running.
System Specifications are:
2011+ J-LX/J-LXL/
2011-2013 J-375/J-365/J-355/J-345/J-335
CLEAR
RAY
• Circulation pump and CLEAR
RAY
run 8 hours (unless altered). Cycle starts approximately two minutes after
power up.
• CLEAR
RAY
shuts off when either JETS button is pressed. It will resume operation approximately 5 minutes
after jets are turned off intentionally or automatically. The CLEAR
RAY
also shuts off if the hot tub goes into
“summer logic.” See Section 5.4 (page 14).
2011-2013 J-325/J-315 Ozone System Specifications
J200 Ozone System Specifications (Models with a Circulation Pump)
• Circulation pump and CLEAR
RAY
run 24 hrs. Cycle starts approximately two minutes after power up.
• CLEAR
RAY
shuts off when either JETS button is pressed. It will resume operation approximately 5 minutes
after jets are turned off intentionally or automatically. The CLEAR
RAY
also shuts if the hot tub goes into
“summer logic.” See Section 5.4 (page 14).
J-200
CLEAR
RAY
System Specifications (Models without Circulation Pump)
• The CLEAR
RAY
will run whenever jets pump 1 is running.
5.0 Additional Control Panel Functions
5.1 Setting Water Temperature and Overtemp Feature
1. Press WARMER or COOLER button once and release while the current water temperature is
displayed to view the current temperature setpoint, then;
2. Press WARMER or COOLER button within 3 seconds to increase or decrease set temperature
setpoint in 1 degree increments as desired. Water temperature can set to any value within 65-
104°F (18-40°C);
3. After 3 seconds of keypad inactivity the LED display will return to actual water temperature and
the new temperature setpoint will be maintained.
4. To access the overtemp feature that allows the spa to reach 106ºF (41ºC) follow the steps below:
A. Press and hold the WARMER button then;
B. Press and hold the JETS 1 button at the same time for 2 seconds. You will see the tempera-
ture rise to 106ºF (41ºC) on the LED display. To lower the temperature, press the COOLER button.
C. When the overtemp has been activated, the white decimal point after the last digit will flash on and off
every second as an indicator for being in the overtemp mode.
Note:
Once the temperature goes below 104ºF (40ºC) and you would like to raise the temperature to 106ºF
(41ºC) again, you will have to repeat step 4 above.
2011-2013
J300 models
J200 models
J-LX models
