background image

56

J-445/J-435 Export

4.  Do not walk, sit or stand on the cover.

5.  Do not drag or use the flaps/skirt or the cover lock straps to remove 

the cover.

6.  Use only recommended cover lift systems.

7.  Use only chemicals and cleaners recommended by Jacuzzi.

8.  Remember to keep spa covered when not in use. Maintaining proper 

water levels assures efficient operation and efficient electrical usage. 

9.  Do not expose your spa to the sun for extended periods of time as 

UV rays can damage the interior surface.

10. Use caution when removing cover. Before removing cover, assure all 

locks have been released to avoid lock breakage and or cover strap 

damage.

13.8 Winterizing

Your Jacuzzi spa is designed to automatically protect itself against freezing 

when operating properly. During periods of severe freezing temperatures, 

you should check periodically to be certain that the electrical supply to the 

spa has not been interrupted. In extreme, bitter cold weather 0°C (less 

than 32°F) we recommend that the circulation pump is set for 24-Hour 

operation (Section 12.3 Programming The Primary Filter Cycle, page 

39) and that auto-heating is selected (Section 12.1 Auto-Heating, page 

38) to protect against damage to the spa.

If you do not intend to use your spa, or if there is a prolonged power 

outage during periods of severe freezing temperatures, 

it is important 

that all water be removed from the spa and equipment to protect 

against damage from freezing.

Expert winterization of your spa is highly recommended; contact 

your authorized Jacuzzi dealer.

 In emergency situations, taking the 

following steps can minimize damage:

CAUTION:

 

TURN OFF POWER TO SPA.

1.  Follow the directions on page 52 for draining the spa.

2.  Turn the massage/diverter selector(s) into the middle combo position 

to allow the water in the plumbing lines to drain, page 36.

3.  Turn the waterfall valve to the open position to allow the water in the 

plumbing lines to drain, page 36.

4.  As the water level drops below the seats, use whatever means 

necessary to get the water out of the recessed seating areas and 

into the footwell, such as a wet/dry vacuum.

5.  Open all the air controls and leave them open until you resume use 

of the spa, page 36.

6.  When the water level ceases to drop, use whatever means available 

to remove any remaining water from the footwell, such as a wet/dry 

vacuum.

Содержание J-435

















































































Отзывы: