background image

J-200

17.5  Wireless Remote Battery Replacement Procedure

1.  Turn the remote unit over and locate the battery door 

(Figure A).

2.  Rotate the battery door, with a coin, counterclockwise to 

the Open position (Figure B). When the door is unlocked it 

will pop up slightly.

3.  Remove battery door by lifting the door upward (Figure C). 

4.  Replace battery using CR2430 or equivalent (Figure D).

5.  Reinstall the battery cover, using the coin rotate the door  

to the Close position (Figure E).

Note:

 Remote unit is water resistant not waterproof. Although it is 

designed for use while in the spa, it should never be left in the spa while 

the cover is on and spa is not in use. The remote should be stored in a 

dry location such as the stereo remote pouch (if applicable) located on 

the outside of the spa cover or within your home. Extreme weather can 

a

ffect the remote control battery. In extreme hot or cold environments 

store the remote control indoors to prolong battery life.

17.6  Bluewave Spa Stereo System Specifications

Power supply  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10.7-14.4V DC

Tuner

FM radio sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8uV

FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Stereo

OPEN

CLOSED

CR

24

30

3V

Fig. A

Battery 

Door

OPEN

CLOSED

C

R

24

30

3V

Fig. B

OPEN

CLOSED

C

R

24

30

3V

Fig. C

CR2430

3V

OPEN

CLOSED

Fig. D

OPEN

CLOSED

CR

243

0

3V

Fig. E

59

Содержание J - 280

































































Отзывы: