background image

J-200

CAUTION: 

Never spray cabinet with a garden hose for any 

reason since this action may induce an electrical short in the 

spa’s electrical equipment.

12.7 Winterizing

Your Jacuzzi spa is designed to automatically protect itself against 

freezing when operating properly. During periods of severe freezing 

temperatures, you should check periodically to be certain that the 

electrical supply to the spa has not been interrupted. In extreme, bitter 

cold weather less than -20°F (-29°C), choose the F3 “Standard” filtration/

heating mode to prevent freezing (page 29). If you do not intend to 

use your spa, or if there is a prolonged power outage during periods 

of severe freezing temperatures, 

it is important that all water be 

removed from the spa and equipment to protect against damage 

from freezing.

Expert winterization of your spa is highly recommended, contact 

your authorized Jacuzzi dealer.

 In emergency situations, damage can 

be 

minimized

 by taking the following steps:

CAUTION: TURN OFF POWER TO HOT TUB!

Follow the directions on page 36 for draining the spa.

1.  Turn off power to the spa.

2.  As the water level drops below the seats, use whatever means 

necessary to get the water out of the recessed seating areas and 

into the footwell, such as a wet/dry vacuum.

3.  Turn the massage/diverter selector(s) into the middle combo position 

to allow the water in the plumbing lines to drain, see page 27.

4.  Turn the waterfall valve to the open position to allow the water in the 

plumbing lines to drain, see page 23 and 24.

5.  As the water level drops below the seats, use whatever means 

necessary to get the water out of the recessed seating areas and 

into the footwell, such as a wet/dry vacuum.

6.  When the water level ceases to drop, use whatever means available 

to remove any remaining water from the footwell, such as a wet/dry 

vacuum.

7.  Remove the synthetic cabinet panel under the control panel and 

locate the drain plugs on the front of the pump(s), (Figure A, page 

15). Remove plugs to allow water to drain out of pumps and 

heater.

Note:

 Approximately one to two gallons will be released during this 

procedure. Use a wet/dry vacuum or other means to keep this from 

flooding the equipment compartment. Replace the drain plugs.

8.  Loosen hose clamp at bottom of CLEAR

RAY

® system and pull hose 

off of CLEAR

RAY

 fitting (twist the hose back and forth while pulling 

downward). Tip hose down and allow to drain. Then reinstall hose 

and clamp. Remove the cover of the CLEAR

RAY

 system to access 

the UV bulb and quartz tube. Remove and store the UV bulb in a 

38

Содержание J - 280

































































Отзывы: