background image

J-200

14.11  Panel Displays T--OH

 

WARNING:

 

RISK OF HYPERTHERMIA (OVER-HEATING) 

CAUSING SEVERE INJURY, BURNS, OR WELTS.

!

Water temperature is above acceptable limits. 

DO NOT  

ENTER SPA!

 Water temperature has reached 112°F (44°C). 

The Jets Pump 1 has activated to circulate water through 

heater. Contact your authorized Jacuzzi dealer or qualified service 

technician. The display will alternate between 

“T--OH”

 and the current 

water temperature.

Note:

 As a safety measure, the red lights of the spa will flash on and off 

as an indication that the spa is an overheat condition.

To correct condition:

•  Remove the spa’s cover and allow your spa to cool down.

•  Program the heater settings for Economy Mode (page 31).

•  If the condition persists, contact your authorized Jacuzzi dealer.

14.12  Panel Displays H--OH

 

WARNING:

 

RISK OF HYPERTHERMIA (OVER-HEATING) 

CAUSING SEVERE INJURY, BURNS, OR WELTS.

!

Hi-limit temperature is above acceptable limits. 

DO NOT  

ENTER SPA!

 Water temperature has reached 112°F (44°C). 

The Jets Pump 1 has activated to circulate water through 

heater. Contact your authorized Jacuzzi dealer or qualified service 

technician. The display will alternate between 

“H--OH”

 and the current 

water temperature.

Note:

 As a safety measure, the red lights of the spa will flash on and off 

as an indication that the spa is an overheat condition.

14.13  Panel Displays (-- -- -- --)

 

WARNING:

 

RISK OF HYPERTHERMIA (OVER-HEATING) 

CAUSING SEVERE INJURY, BURNS, OR WELTS.

!

Water temperature is above acceptable limits. 

DO NOT  

ENTER SPA! 

The safety “Watchdog” software has been 

triggered and the spa is deactivated. A problem has been 

detected which could cause damage to the spa or its components. The 

display will alternate between 

“-- -- -- --”

 and the scrolling message 

“WATCHDOG CALL FOR SERVICE”

 as long as the error exists. 

Contact your authorized Jacuzzi dealer or qualified service technician.

Note:

 As a safety measure, the red lights of the spa will flash on and off 

as an indication that the spa is in watchdog condition.

50

Содержание J-200 Series

































































Отзывы: