background image

© 2019 Jackson Labs Technologies, Inc.

73

Micro-JLT GNSS™ User Manual

Certification and 

Warranty

6.1 Certification

Jackson Labs Technologies, Inc. certifies that this product met its published specifications at time of 
shipment.

6.1.1 Warranty

This Jackson Labs Technologies, Inc. hardware product is warranted against defects in material and 
workmanship for a period of 1 (one) year from date of delivery. During the warranty period Jackson 
Labs Technologies, Inc. will, at its discretion, either repair or replace products that prove to be 
defective. Jackson Labs Technologies, Inc. does not warrant that the operation for the software, 
firmware, or hardware shall be uninterrupted or error free even if the product is operated within its 
specifications.
For warranty service, this product must be returned to Jackson Labs Technologies, Inc. or a service 
facility designated by Jackson Labs Technologies, Inc. Customer shall prepay shipping charges (and 
shall pay all duties and taxes) for products returned to Jackson Labs Technologies, Inc. for warranty 
service. Except for products returned to Customer from another country, Jackson Labs Technologies, 
Inc. shall pay for return of products to Customer. If Jackson Labs Technologies, Inc. is unable, within 
a reasonable time, to repair or replace any product to condition as warranted, the Customer shall be 
entitled to a refund of the purchase price upon return of the product to Jackson Labs Technologies, 
Inc.

6.1.2 Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance 
by the Customer, Customer-supplied software or interfacing, unauthorized modification or misuse, 
opening of the instruments enclosure or removal of the instruments panels, operation outside of the 
environmental or electrical specifications for the product, or improper site preparation and 
maintenance. 

JACKSON LABS TECHNOLOGIES, INC. SPECIFICALLY DISCLAIMS THE 

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 

Содержание Micro-JLT GNSS




















































































Отзывы: