The JA-82Y GSM communicator installers manual
5/13
MDL51109
Only characters which can be keyed in from the system keypad (0 to 9, * and
#) can be used in the sequences
When a valid instruction is received, the communicator performs the sequence
by simulating entering the keys on the keypad. A comma in the SMS is taken
as a pause in the sequence entering.
If you want to remotely reprogram the system it must first be unset and then
switched to programming mode
The number of sequences in one SMS is limited by the maximum size of the
SMS in the GSM network.
Example:
by sending SMS
8080_PRG_
08080_201_#
the exit delay will be set
to 10s
6.23. Registration code
You need to know the communicator registration code when first connecting via
the OLink software through the Internet. The code is stated on the label on the
communicator panel but it can also be sent to the mobile phone by SMS. To
request a registration code, enter:
911 xx...x
0
where
xx...x
is the number of the phone where the code should be sent
Notes:
The time needed for delivery of the code depends on the current GSM network
speed
Each communicator has a unique registration code in the following format:
xxxxx-xxxxx-xxxx
6.24. Remote access password
This security key for data communication is a condition for remote access to the
system via OLink program. It is set through the following sequence:
894 xxx …x
0
where:
xxx…x
is a security access password which can have 1 to 32 digits
Note:
If a password using letters is required, it must be set in the OLink software or
by an SMS message. Letters are case-sensitive.
Factory default setting:
1234ABCD
6.25. Restarting GSM communication
After
893
has been entered, the communicator disconnects from the GSM network
and then re-registers itself. This re-registration does not change any settings in the
communicator. It should be used after GSM network faults or data collisions and in
some networks it also has to be used after a blocked SIM card has been
unblocked by the GSM provider. It is also possible (if the SIM card can still receive)
to trigger GSM network re-registration by sending the SMS instruction:
code GSM
6.26. Communicator reset
Entering 998080 returns the communicator to its factory default settings.
Telephone numbers will be erased together with all untransmitted reports but the
text settings in the communicator will not be changed.
6.27.
SIM card’s PIN code
It is recommended to use a SIM card with disabled PIN protection in the
communicator. If you still want to use a card with PIN protection, enter the PIN by
entering the following sequence (it must be entered after the control panel has
been powered up):
920 PIN
0
Example:
If the SIM card PIN code is 1234, enter
9201234
0
Notes:
If the communicator does not register to the GSM network within 1 minute of
the PIN being entered (this problem is shown by the red LED flashing), then
you either entered a wrong PIN or the GSM signal is too weak. In such a case:
enter 920*0 while in control panel service mode (erases the PIN entered in the
communicator)
disconnect the control panel power (mains and battery)
take out the SIM card, insert it into a mobile phone and check whether the PIN
is correct. Check whether the signal strength at the location of the control panel
is sufficient
if you know the right PIN code and the GSM signal is strong enough, put the
SIM card back into the communicator, turn on the control panel power and then
enter the correct PIN code (920 PIN *0) and wait until the communicator
registers to the GSM network (its red LED should turn off within a minute)
The communicator memorizes the set PIN and it will use it automatically
whenever it registers to the GSM network again.
If you are replacing the SIM card in the communicator with another one and the
former one used a PIN code, first switch the control panel to service mode and
enter 920*0 to erase the former PIN code. The SIM card can then be changed.
Warning:
The PIN code cannot be changed if the ARC settings are locked
Factory default setting:
The PIN code is erased
6.28. GPRS parameter setting
GPRS data communication (wireless Internet via a GSM network) is used for
remote access via the OLink software and also for communication between the
system and the ARC. To use GPRS data communication it must first be enabled
(activated) in the SIM card (contact your GSM provider for details). Depending on
the SIM card used, the GPRS parameters (APN and possibly the login and
password if the SIM card requires them) must be programmed by sending the
following SMS instruction to the communicator.
code_GPRS_ x..x_y..y_z..z
where:
Code
valid service system code (e.g. 8080 )
_
space
x..x
SIM card APN
y..y
username (do not enter if not required)
z..z
password (do not enter if not required)
Examples:
For a T-mobile Czechia card enter: code GPRS internet.t-mobile.cz
Warning:
The GPRS parameters cannot be changed if the ARC settings are
locked
Factory default setting: APN = internet
7. Communication to the ARC
7.1. ARC phone numbers
Events can be reported to up to 2 ARCs (which can be independent or ARC2 can
work as ARC1’s backup). Each ARC can have its main and backup phone
numbers (or IP addresses) programmed with:
Main:
01 p xx....x
0
Backup:
02 p xx....x
0
where:
p
1=ARC1, 2=ARC2
xxx...x
tel.
number
(max.20 digits)
or IP address
and port
– entry format
example.:
01 2
8 192 168 001 123 08080
0
where:
8
(auto-converts to #) signifies an IP address which must have 12
digits and must be followed by the 5 digits of the port number (no
separators).
To erase a tel. number / IP address
enter
01p
0
or
02p
0
. If
numbers / IP addresses are erased there will be no reporting to that
particular ARC.
Notes:
the communicator first tries to send data to the main number / address, if it
is not successful it tries the backup number / address.
the ARC address can also be entered as URL (via OLink only)
Factory default setting:
all tel. numbers / IP addresses erased
7.2. Installation (alarm system) ID for ARC use
The installation’s ID number which is sent to an ARC with every report can be
programmed with:
03 p zz..z
0
where:
p
1=ARC1, 2=ARC2, 3=IMG
zz..z
installation ID number, max. 8 characters (0 to 9 and *1=A to *6=F)
Factory default setting:
for all ARCs = 0000
Note:
If you want to transmit photographs, enter 3 in the p parameter
7.3. Selecting the ARC communication protocol
To select the required communication protocol enter:
04 p x
where:
p
1 = ARC1, 2 = ARC2
x
0..2 = ARC type
0 = Contact ID, 1 = Jablotron IP, 2 = Jablotron SMS
Notes:
Jablotron IP is the fastest
of the abovementioned protocols and it is the only
one which
allows very frequent checking of communication reliability
with
the ARC (e.g. every 5 minutes).
Contact ID protocol can be directed to ARCs linked by standard telephone
lines (if they support Contact ID).
If your ARC does not allow Jablotron SMS or Jablotron IP protocols, please
contact a Jablotron distributor for details on how to upgrade your ARC
Factory default setting:
ARC1 - Jablotron IP, ARD2 - Jablotron SMS