JABLOTRON
ALARMS
a.s.
Pod
Skalkou
4567/33
46601
Jablonec
n.
Nisou
Czech
Republic
www
.jablotron.com
||
|
The JA-159P wireless outdoor PIR detector
The JA-159P wireless outdoor PIR detector
1 / 2
MMY51805
The JA-159P wireless outdoor intruder detector is designed
to detect human body movement in an outdoor environment.
It is the VXI-RAM detector produced by Optex with a Jablotron
transmitter. The optical part of the detector has 2 PIR sensors (dual zone
detection) and a high immunity to false alarms and the detection of small
animals. The detector includes an Anti-masking function – protection
against covering the view and it also has two tampers (front and back)
built in. They immediately report opening the detector or attempting
tampering. The detector should be installed by a trained technician with
a valid certificate issued by an authorised distributor.
Installation
Conditions:
1. The detector has to be installed onto a vertical wall (in a position
where its bottom surface is parallel to the watched zone).
2. The detector should be installed 0.8 – 1.2 m above the ground.
3. The best movement detection is provided when the detection beams
intersect.
4. No other moving objects (bushes, trees, high grass, air-conditioners,
etc.) should be situated in the field of view of the detector.
5. Avoid direct effects by strong sources of light (sun reflections, etc.).
Procedure:
1. Unscrew the locking screw on the bottom of the upper cover
of the detector (1) and remove the detection part’s cover (1).
2. Unscrew the 2 screws which hold the detector´s main board (2)
and pull it out by tilting as you pull it out. There is also a radio
transmitter glued onto the rear side of the detector´s PCB.
3. Remove the rear box cap (5) by pulling it up.
4. Unscrew the 2 screws which link the rear cover (3) with the
mounting plate (4).
5. The detector can be mounted onto a level mounting place by the
2 screws through the mounting plate (4). Or it can be mounted
on a pole by metal ties (not supplied).
6. Put the detector parts back together in the opposite order when
it´s finally fixed to the mounting place (4).
Warning: Do not touch the detector sensing face
during handling
If it does happen, it´s necessary to clean it up by a
cotton swab dipped in alcohol.
1
2
3
4
5
Fig. 1.: 1 – front cover, 2 – detector main board, 3 – rear cover,
4 – mounting plate, 5 – rear cover cap
Fig. 2.: Detector installation. Standard wall installation and fixing by ties.
Enrolling the detector to the system
The signal transmitter for wireless communication is located under
the main board part of the detector. The batteries are inserted into the
battery holder placed on the transmitter PCB.
Use two CR123A
(3 V, 1500 mAh) lithium batteries from the same manufacturer and
replace both batteries at the same time.
The correct position of the
batteries is indicated on the battery holder.
Enrollment procedure to the system:
a. Go to the
F-Link
software, select the required position in the
Devices
window and launch the enrollment mode by clicking on
the
Enroll
option.
b. Insert the batteries (mind the correct polarity). When the first
battery has been inserted into the battery holder an enrollment
signal is transmitted to the control panel and the detector is
enrolled to the selected position.
c. Assemble the detector in opposite order to which it was
disassembled.
Fig. 3 - Transmitter:
1 – terminals for connection to the detector,
2 – red indication LED; 3 - yellow indication LED; 4 - battery holder;
5 – external antenna connector; 6 – production code
Notes:
-
There must be a JA-110R radio module installed in the control
panel.
-
The detector can also be enrolled into the system by entering its
production code (9) in the F-Link software. You can find the
production code on the sticker, glued onto the PCB. All numbers
under the bar code shall be entered (1400-00-0000-0001).
-
If needed the transmitter can be equipped with an AN-868
(3 PIN) external antenna connected to the connector (5).
Normal operating mode
The detector sends a radio signal about activation when it is
triggered. In the case of tampering with the detector or tearing the
detector off its position the detector sends a tamper signal. Every
9 minutes a status report is sent to the control panel.
Replacing the batteries
The detector checks its battery status automatically and if the
batteries are running low it informs the system. The detector remains
fully functional. The batteries should be changed as soon as
possible.
Before battery replacement
the control panel has to be switched
to service mode (see installation manual of the control panel) and
then it is possible to open the cover of the detector. Always use
CR123A (3V, 1500 mAh) batteries.
Setting up the optical part of the
detector
The optical part of the detector includes 2 PIR sensors with AND
logic. They detect movement in two planes. The detecting angle of
the lower PIR sensor can be adjusted. The alarm signal is triggered if
only both detecting planes are triggered at the same time. By shifting
the lens set up the tilt of the lower detecting plane according to the
following picture and table.
Fig. 4.
