Contactless access control system RP-01
1/1
VAB50202
Contactless access control system RP-01
This device works as a reader of chips (PIT) or cards (PIT). You can
program it with buttons or PC application. This product provides data
connection (RS485), therefore it can be used even for industrial
applications.
1. Technical
parameters
Operating Voltage
9 ÷ 16V DC or 8 ÷ 12V AC
Standby current
35mA
terminals NO,C,NC
output relay – switching contact max. 1A/125V
operation:
control unit – II. indoor use (-10°C to +40°C)
reading unit – outdoor use (IP46) (-30°C to +60°C)
dimensions (control unit)
2,99 in (w) x 4,3 in (h) x 1,299 in (d)
JabloPCB s.r.o. declares this product is in an agreement with common
requirements and other related EU regulations.
The original of the statement is posted at
www.jabloPCB.cz
website in
section Technical support.
2. Installation and basic functions RP-01
2.1. Device installation
MOD SEL SET
RELE
12
V
NO
C
N
C
Interface RS-485
LCD connector
Setting buttons
MOD
SEL
SET
Connector
reading device
Output relay
Power
Control unit
Reader unit
image no 1
The control unit is designed for an indoor installation. During
installation please respect placement of the reading unit as it is
connected with 1m long wire. The reading unit can be placed outdoors.
Warning: reading unit’s wire can be shortened to 0,5m. Replacement
with the different one or extension is disabled as device will not function
correctly.
•
prior to control unit installation remove the plastic cover
•
take an LCD off the control unit by pulling it out – display is
attached with connector (see image no 1)
•
connect the reading unit to the connector (see image no 1)
•
check and attach power to the 12V terminals
•
place and fit the unit in the desired space
•
return LCD back to the original placement (pay extra attention
to attaching to the connector)
•
switch the control unit‘s power on
•
you will see a basic initialization on the LCD
•
and the unit is ready to be used
2.2. Basic setup
Unit was already set in the factory and is ready to learn (program)
individual positions. There are 999 position ava master chip
position.
2.3. Unit learning (PIT – chips and cards)
Programming is possible either with PC controlling software (you
need to connect interface SW-01) or manually with buttons placed
under the LCD and instructions on the screen.
The Master Chip necessary to enter the learning mode is included in
the package.
Table – reading unit indicator signals
indicator
Description
No light
Ready to program
Green light
PIT was identified and successfully learned
learning
Red light
PIT was already programmed to a different
position
No light
Unit is ready to read PIT
Green light
PIT authorized to enter – relay ties
Pulse
mode
Red light
PIT unauthorized to enter – relay doesn’t tie
Green light
Relay OFF
Red light
Relay ON
Switching
mode
No light
Unknown PIT is read and indicator switches off
for 1s
Manual way:
There are
MOD
button and
Master Chip
to enter the programming
mode.Press and hold the
MOD
button for at least 2s and display will
show „
check MASTER
“. On this command place Master Chip on the
reading unit. Following that you will gain access into the learning mode
and first available position for programming individual PIT will be
offered.
If you don’t want to start learning individual PITs from this position you
can set any position by pressing the
SEL
button.The bottom row on the
screen displays the position selection options (with each press of the
SEL
button).
SEL
button setting options:
Po100
and consequently every press of SET button – position
is set for hundreds 100, 200, 300...
Po10
and consequently every press of SET button – position is
set for tens 10, 20, 30...
Po1
and consequently every press of SET button – position is
set for ones 1, 2, 3...
(settings can be combined. For example you can set 100 then 10 and 3
= result is learning position 113)
RELAY time
– see point 2.5
DELETE ?
– current position will be deleted by pressing the
SET
button
Return to the learning mode
Setting of each option is made by pressing the
SET
button (it has got a
repeat function when pressed and held). Press
MOD
button to end
settings.
To exit learning mode press and hold
MOD
button. Device will go into
standby mode.
It is possible to re-program or delete any position except a learning
position „
master position“
(see point 2.4).
Programming using PC application is more convenient as you can work
with files like CSV (export from Excel). The first column has to be a
learning position and the second column needs to be selected PIT´s
manufacturing code. Ignore the other possible columns.
Warning:
During learning new PIT chip on an available position or into an empty
space (caused by deleted position) follow these instructions.
Access the learning mode (see point 2.3). When first available position
is offered, programm PIT by placing it on the Reading Unit. Also you
can decide which position to use at this stage. After the process of
programming the Reading Unit will offer you the next one up position.
In
case this position has already been programmed to a PIT and you
use this position to learn a new PIT, the previous one will be
deleted.
