Jabiru j160 Скачать руководство пользователя

Страница: 42 / 298

Aircraft Technical Manual

Jabiru Aircraft

Pty Ltd

J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

Dated: 29th October 2014

Issued By: AS

Page: 42 of 298

Inspection & Servicing

5.1

Service Interval Tolerance



A tolerance of plus or minus 3 hours is allowable on all service intervals set within this manual

5.2

Basic Inspection Procedure



Remove the engine cowlings and inspect the engine bay in “dirty” condition.



Clean the engine bay, propeller and aircraft exterior.



Carry out the inspections listed in Table 5-1.



Test and re-assemble the aircraft. Test fly if required.

5.3

Mandatory Inspections & Lifed Items

5.3.1 Airframe



At intervals of 5000 hours the Jabiru (all models) airframe must be subject to an overall condition

inspection by Jabiru Aircraft or an aircraft maintainer authorised by Jabiru Aircraft. As part of this
inspection, wing struts must be disassembled, inspected for damage using appropriate NDT methods
(such as dye-penetrant testing).



Jabiru aircraft do not have an overall airframe life limitation.

5.3.2 Control Cables



Control cables for all aircraft are subject to the inspection and replacement requirements detailed in

Section 22.

5.3.3 Engine Bay Flexible Hoses



All flexible hoses in the engine compartment should be replaced at engine overhaul or every 2 years

whichever comes first. Hoses which show visible deterioration (cracking, excessive hardening) must
be replaced immediately, irrespective of age.

Содержание j160











































































































































































































































































































Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды

Jabiru j160, Техническое руководство

Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды