Jabiru j160 Скачать руководство пользователя | Manualshive

Страница: 198 / 298

background image

Aircraft Technical Manual

Jabiru Aircraft

Pty Ltd

J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

1

2

3

4

5

Dated: 29th October 2014

Issued By: AS

Page: 198 of 298

7.2

Engine (all J-Series)

7.2.1 Description



The engines used in Jabiru Aircraft are horizontally-opposed, 4-stroke air-cooled designs, driving a

fixed-pitch wooden propeller. 80hp, 4-

cylinder “2200” versions are used in the J120, J160 and J170

model families while the 120hp, 6-

cylinder “3300” engine is used in the J200, J230 and J250 model

families. In some kit-built variants the 3300 engine may also be used in the smaller aircraft.



The front Starboard cylinder is numbered 1, the front Port is numbered 2 with this numbering

convention continuing for the remaining cylinders.



Refer to Engine Maintenance Manual for detailed engine data.



For repair & overhaul of the engine, refer to the Overhaul Manual issued by Jabiru Aircraft Pty Ltd.

7.2.2 Engine Data



Refer Engine Maintenance Manual

7.2.3 Engine Removal & Installation



Refer Engine Maintenance Manual

7.2.4 Engine Trouble Shooting



Refer Engine Maintenance Manual

7.2.5 Engine Cleaning



Refer to Section 4.1 & the Engine Maintenance Manual.

7.2.6 Engine Accessories



Jabiru engines may be fitted with an accessory vacuum pump, mounted to a pad at the rear of the

engine.



All Jabiru engines are fitted with a permanent magnet alternator at the rear of the engine. This is

considered a part of the engine and is discussed in the Engine Maintenance Manuals.



Removal, inspection and installation of accessories are discussed in the appropriate Engine

Maintenance Manual.

7.2.7 ENGINE Inspections



For specific items to be inspected and for periodic inspection details, refer to Engine Maintenance

Manual.



Generally, inspect for:

-

Loose bolts, nuts, cracks, leaks & cooling fin damage

-

Inspect baffles, baffle seals & brackets for cracks, deterioration or damage.

-

Inspect hoses for internal swelling, chafing, cuts, breaks, stiffness or loose connections.
Excessive heat on hoses will cause them to become brittle & easily broken. Hoses are most likely
to crack or break near the ends & at support points. Check fire sleeves on fuel lines within the
engine compartment.

-

All flexible hoses in the engine compartment should be replaced at engine overhaul or every 2
years whichever comes first. Hoses which show visible deterioration (cracking, excessive
hardening) should be replaced immediately, irrespective of age.

-

For major engine repairs, refer to Jabiru Aircraft Pty Ltd or an Approved Jabiru Service Centre.

«
...
196
197
198
199
200
...
»

Содержание j160











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для j160

Floater Altitude 2,4 GHz

Бренд: Jamara Страницы: 12

Бренд: LEGO Страницы: 84

Бренд: Trix Страницы: 60

Бренд: marklin Страницы: 32

Бренд: E sky Страницы: 32

B&O 0-4-0 DOCKSIDE

Бренд: AML Страницы: 8

Бренд: BLOTZ Страницы: 2

Fun 2 Learn J6870

Бренд: Fisher-Price Страницы: 8

Бренд: Opale-Paramodels Страницы: 6

Бренд: Carrera RC Страницы: 40

My Little Baby Born I Can Swim!

Бренд: Zapf Creation Страницы: 4

Бренд: battat Страницы: 2

Бренд: Hornby Страницы: 2

Бренд: Condor Страницы: 7

Бренд: Betzold Страницы: 5

kubros T-800 GUARDIAN

Бренд: SKYDANCE Страницы: 32

Бренд: Faller Страницы: 8

Eurofighter Typhoon V2

Бренд: Freewing Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды