Jabiru j160 Скачать руководство пользователя

Страница: 169 / 298

Aircraft Technical Manual

Jabiru Aircraft

Pty Ltd

J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

Dated: 29th October 2014

Issued By: AS

Page: 169 of 298

6.60 External Flap Push Rod (all J-Series)

6.60.1 Description



The external flap push rods connect the flap cross shaft to the flaps.

6.60.2 Removal, Inspection & Installation

Required Tools:

Spanners / Socket Wrench

Parts and Material:

Heavy duty tape

Type of Maintenance:

Line Maintenance

Level of Certification:

L1, L2 or LAME (Owner, A&P or LSA Repairman / Maintenance)

Return to Service:

L1, L2 or LAME (Owner, A&P or LSA Repairman / Maintenance)



Apply heavy duty tape or similar to both wing flaps, holding them up.



To remove, unbolt at both ends and remove. Reverse for installation.

WARNING

All spherical rod end bearings must be fitted with a large washer on the outside of the through-

bolt to prevent the bearing case and cable releasing in the event of a bearing failure.

6.61 Flap (all J-Series)

6.61.1 Description



The flaps comprise a moulded and bonded monocoque structure embodying a composite control

arm at the inboard end.



Installation drawings for flaps are given in Section 0.

6.61.2 Flap Removal

Required Tools:

Spanners / Socket Wrench

Parts and Material:

N/A

Type of Maintenance:

Line Maintenance

Level of Certification:

L2 or LAME (A&P or LSA Repairman / Maintenance)

Return to Service:

L2 or LAME (A&P or LSA Repairman / Maintenance)

Unbolt rod end from flap control arm.

Remove each flap hinge bolt and spacer.

Remove Flap.

6.61.3 Inspection And Repair

Required Tools:

N/A

Parts and Material:

N/A

Type of Maintenance:

Line Maintenance

Level of Certification:

L2 or LAME (A&P or LSA Repairman / Maintenance)

Return to Service:

L2 or LAME (A&P or LSA Repairman / Maintenance)



Inspect flaps for any signs of delamination or cracking. Pay particular attention to the Control Horn

and hinges and their surrounding areas.



Repairs must be referred to Jabiru Aircraft Pty Ltd or our approved local agent.

Содержание j160











































































































































































































































































































Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды

Jabiru j160, Техническое руководство

Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды