Jabiru 2200 Скачать руководство пользователя страница 54

Страница: 54 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 54 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

5.3 Mandatory Replacement Items

– Top End Overhaul

Table 4

– Mandatory Replacement Items – Top End Overhaul

Items To Be Checked & Re-Used If Good

Items To Be Replaced

Distributor seals

All necessary mods, plus:

Crankshaft front seal

Connecting rod bearings

Valve springs

Connecting rod bolts

Valve rockers (and adjusters for solid lifter engines)

Intake and exhaust valves

Rocker shafts

Pistons, piston gudgeon pins and circlips

Pushrods

Piston rings

Pushrod tubes

Cylinder base O rings

Rocker bushes

Spark plugs

Cylinders: measure & hone.

Fuel pump gaskets

Distributor caps & rotors

Cylinder head bolts

Ignition coils

Induction tube joiners

Ignition leads

Oil filter

Fuel pump

Oil pump O rings

Cylinder heads

All cylinder head O rings

Valve guides

All intake & exhaust gaskets

Fuel hoses

All intake & exhaust cap screws

Air filter

Valve lifters (hydraulic)

Carburettor rubber mount

Engine through bolts

Carburettor

– check jetting & float levels

Crankshaft rear seal

Flexible oil hoses

Flywheel cap screws

Oil pump assembly

Crankshaft timing gear

Oil relief valve assembly

Propeller flange cap screws

Alternator stator & rotor (magnet ring)

Rubber T

– from rocker oil feed line

Starter motor & starter motor clutch

Camshaft (visual check of lobes)

Содержание 2200










































































































































































































Результаты поиска

Содержание 2200

Отзывы:

Jabiru 2200, Руководство по капитальному ремонту, Страница: 54 / 201

Результаты поиска

Содержание 2200

Отзывы: