Jabiru 2200 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 201

background image

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

1

2

3

4

5

6 7

Dated : 28/10/2014

Issued By: AS

Page: 37 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

Figure 41

– Using A Crowsfoot Adaptor

3.8.3 Torque Application Procedure



Good torque application technique is essential if an accurate bolt torque reading is going to be

obtained.



Firstly the nut must be tightened smoothly. Any jerks or bumps can cause the torque reading to be

obtained prematurely.



The torque must be obtained while the nut is turning. If you stop to reposition the torque wrench

and then the required torque reading is obtained without the nut turning, the nut needs to be
loosened a little and then tightened again so the torque reading is obtained while turning.



Unless specified otherwise all torque settings given in this manual are “dry” – i.e. no special
lubricant is applied to the threads or parts. Where directed otherwise it is vital that the directions are
followed exactly.

Corrected Torque Setting Required

No Correction Required.

«
...
35
36
37
38
39
...
»

Содержание 2200










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2200

Бренд: Paccar Страницы: 71

Бренд: BAFANG Страницы: 12

Бренд: EuroLite Страницы: 19

Бренд: Briggs & Stratton Страницы: 102

Бренд: Kohler Страницы: 116

Бренд: VEM Страницы: 35

Бренд: Yanmar Страницы: 38

Бренд: Chris-Craft Страницы: 39

Lombardini SILEO 1000

Бренд: Kohler Страницы: 168

Бренд: VDG Страницы: 18

PNEUTORQUE PT 1

Бренд: norbar Страницы: 11

PowerLine TG500B

Бренд: Texas Страницы: 98

Бренд: Inel Страницы: 4

Бренд: Hacker Motor Страницы: 4

Бренд: YS Страницы: 2

Бренд: Volvo Страницы: 20

Бренд: Volvo Страницы: 51

Бренд: Volvo Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды