Jabiru 2200 Скачать руководство пользователя страница 15

Страница: 15 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 15 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

2.10 Mandatory updates



Jabiru has been producing engines for many years, and over that time we have made some

improvements to our engine designs in light of operating experience. As a result we have compiled a list
of mandatory updates that must be made to older engines during overhaul.



During the Inspection and assessment stage these modifications will be addressed for each

Subassembly.



The requirements of these modifications must be taken into account when ordering parts.



Section 10 refers.

2.11 Mandatory replacement of parts



During overhaul (either complete or top end) some parts must be replaced regardless of condition: for

example all bolts, all seals, O-rings, etc. Detailed listings will be found in the Inspection and assessment
stage.

2.12 Recording



Careful records of all overhauling work must be completed. It is strongly recommended that the

overhauler print out the build sheets given as a part of this manual and use them to record all the details
of the job.



The overhaul booklets included in Section 9 are to be used for a top end overhaul

– using only those

pages relevant to the parts of the engine being renewed.

Содержание 2200










































































































































































































Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды

Jabiru 2200, Руководство по капитальному ремонту

Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды