J.P. Instruments FS-450 страница 20 Скачать руководство пользователя

Страница: 20 / 28

Page 18

FS-450 Fuel Scan

Setting GPS-C Communications Output Format

GPS-C

Input to GPS; output of FS-450

No fuel data output

1 *

Garmin (Shadin Miniflow format) (to waypoint)

2 *

Allied Signal (format B) (to waypoint)

Arnav/EI fuel data

(to waypoint)

Allied Signal (format C) (to waypoint)

(Not used)

Garmin 430/530/295, UPS fuel/air data (to WAYPOINT)

Garmin 430/530/295, UPS fuel/air data (to DESTINATION)

Allied Signal (to DESTINATION)

* Recommended formats.

GPS Interface Diagnostic Messages

Parameters

REQ - RES - MPG

are

all missing from the scan.

No communications from GPS
receiver to FS-450. Possibly no
connection or aircraft GPS is off,
or GPS not enabled to output data.

message and parameters

REQ - RES - MPG

are missing

from scan.

Communications are received by
FS-450 and the Auto-Protocol
setup is in process. Verify correct
output format setup in GPS
receiver; check GPS connections.

message and

parameters

REQ - RES - MPG

are

missing from scan.

GPS receiver has insufficient
signal for valid data.

message and parameters

REQ - RES

are missing from

scan.

No waypoints are programmed
into the aircraft GPS receiver.

replaces

REQ

RES

Your ground track is more than



70° from your course to the next

GPS waypoint.

Содержание FS-450





























Результаты поиска

Содержание FS-450

Отзывы:

Похожие инструкции для FS-450

Бренды по названию

Популярные бренды

J.P. Instruments FS-450, Руководство пилота

Результаты поиска

Содержание FS-450

Отзывы:

Похожие инструкции для FS-450

Бренды по названию

Популярные бренды