J.A. Woollam M-2000 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 178

background image

M-2000® Hardware Manual

©2023 J.A. Woollam Co.

141

9.

Insert the new QTH lamp into the holder and ensure it is seated down
fully. Note the polarity of the lamp connectors and the base; the lamp
will only go in the base one way.

10.

Replace the cover.

11.

Tighten the SHC screws to lock the cover closed.

12.

Reset the hour meter by pressing the reset button located on the front of
the M-2000 Detector and Lamp Power Supply Module.

Note:

When a new lamp is installed, it must be aligned so that the
maximum amount of light is available for sample measurement.
The optimal position should not change much from lamp to lamp,
but fine adjustment is needed to achieve best results.

Lamp Alignment

After the lamp(s) has been replaced it is recommended that the lamp housing be
aligned for maximum intensity. For the XLS-200, no lamp adjustment is
necessary.

1.

Turn on the lamp power supply. Allow the lamp to warm up for at least
20 minutes.

2.

Ensure the Base is in the 90° (straight-through) position and the Z-
position is raised such that the sample stage will not block the beam from
hitting the receiver unit’s aperture.

3.

Slightly adjust the source unit tilt stage to center the beam on the
receiver aperture if necessary.

4.

Open the alignment screen by selecting

Hardware

>

Controls

>

General

>‘Align Sample’. Choose No when

prompted for the full system alignment.  If your system has Auto Tip-Tilt,
ensure 'Receiver’ is selected in the Detector panel at the top of the
screen. Verify the cross hair is centered.  If not, slightly adjust the
receiver unit tilt stage to center the cross hair.  See Chapter 4 for more
details.

10.2

Xe Lamp (M-2000X, XI, X-
210, & XI-210) in FLS-860

This section describes installation/replacement, alignment, and cleaning of the
lamps used in the FLS-860 Light Source (for M-2000X, XI, X-210, and XI-210
systems).

«
...
139
140
141
142
143
...
»

Содержание M-2000



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M-2000

Бренд: M3S Страницы: 40

Бренд: Eaton Страницы: 43

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

DC1500 CHLORINE

Бренд: LaMotte Страницы: 60

Бренд: TC Electronic Страницы: 20

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: Veeder-Root Страницы: 39

Бренд: Veeder-Root Страницы: 98

Бренд: VECTECH Страницы: 9

Бренд: Mini Страницы: 20

Бренд: Hilti Страницы: 146

FrameSaver SLV Series

Бренд: Paradyne Страницы: 39

Бренд: Opus Technologies Страницы: 24

Бренд: JBM Страницы: 4

Бренд: GREISINGER Страницы: 20

Бренд: Global Sources Страницы: 2

Бренд: Omega Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды