J.A. Woollam M-2000 Скачать руководство пользователя страница 123

Страница: 123 / 178

M-2000® Hardware Manual

123

Wobble Correction

In order to measure without aligning at each rotator (theta) angle, the wobble
must be removed from the sample stage.

Mount and align the sample (refer to Section

Error! Reference source not

found.

Error! Reference source not found.

) with the theta position at 0°.

Select

Hardware

Controls

System

>‘Translator’ (or ‘Rotator’) and move

the theta position to 180°.

Figure 7-19. Translator Position dialog.

Adjust the Sample Tilt to move the Lookdown cross hair position half of
the distance it has changed.

Figure 7-20. Sample Tilt adjustment.

For example, if X=8, Y=-6.5 : adjust so X=4, Y=-3.25.

Содержание M-2000



















































































































































































Результаты поиска

Содержание M-2000

Отзывы:

Похожие инструкции для M-2000

Бренды по названию

Популярные бренды

J.A. Woollam M-2000, Руководство по оборудованию

Результаты поиска

Содержание M-2000

Отзывы:

Похожие инструкции для M-2000

Бренды по названию

Популярные бренды