background image

 

 
 

 

 

It is mandatory for USBL systems to be calibrated with an INS/AHRS on board of a vessel 

to give accurate position and attitude to the USBL system. Calibration is not necessary with 

Gaps M7 because it contains an INS inside of the USBL head. The calibration is done during 

the manufacture process, making Gaps M7 a precalibrated system. No calibration is nec-

essary by the end user and Gaps M7 can be installed and be operational in less than an 

hour. 

 

Gaps M5 does not need to be calibrated, even after a hydrophone replacement. 

 

 

Gaps systems mixes USBL, INS  and GPS  technologies to give the  most accurate USBL 

data  in  its  category,  it  operates  in  deep  or  very  shallow  water  and  difficult  environments 

where other systems are deficient. As Gaps has an integrated INS, this allows its use with-

out a calibration. Where it is necessary to carefully calibrate all other USBL systems with 

the  INS  on  board,  it  is  not  necessary  to  carry  out  this  calibration  for  Gaps,  as  it  is  pre-

calibrated at our factory with Phins/Octans inside. This will save a lot of time for users and 

Gaps can be operational in less than an hour. The important point to know is that it is nec-

essary to align Gaps to obtain the best accuracy. This means that it is necessary that the 

vessel stay with a constant heading  during 5  minutes  for the coarse alignment, then  it  is 

necessary that it move in different directions for 25 minutes for the fine alignment. In only 

30 minutes, Gaps will be ready to deliver you the specified accuracy. 

 

 

By default the IP address is indicated on the Gaps BOX sticker and is 192.168.36.1XX, with 

XX being the last two numbers of the serial number. If the IP address has been changed 

and is not known, the following steps can be taken. If you have changed the address and 

lost it, you can retrieve this IP address as follows: Connect a hyperterminal on the PC to 

one of the RS232 sockets. Configure the terminal to the following settings: baudrate 115200 

bds, data bits 8, parity: none, stop bits: 1. Reboot the unit by switching it off and on, the IP 

address will be broadcasted by Gaps on the hyperterminal. 

 

 

Содержание Gaps M5

















Отзывы: