iWave iW-RainboW-G21D Скачать руководство пользователя страница 62

Страница: 62 / 106

REL1.0

Page 62 of 106

RZ/G1H Qseven Development Platform Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.8.4

LVDS Port with Resistive Touch (Optional)

The RZ/G1H Qseven carrier board can support LVDS LCD interface through RZ/G1H CPU

’s LVDS

1 display port if LVDS1

port supported RZ/G1H SOM is used

. By default, RZ/G1H CPU’s LVDS1 port is used in the SOM for HDMI transmitter

but have the option to isolate the HDMI transmitter and connect to secondary LVDS channel of the Qseven Edge

connector. These LVDS signals from Qseven MXM connector is directly connected to 20pin LVDS connector (J27). And

LVSD LCD’s power enable and backli

ght enable is connected from GPIO6 (191

pin) & GPIO5 (190

pin) of Qseven

MXM connector which is RZ/G1H CPU’s GPIO pins “

GP4_2

” and “

GP2_1

7” respectively.

This LVDS LCD connector (J27)

is physically located at the bottom of board as shown below.

Compatible LCDs

1. Part Number: OSD104T0571-19TS

Manufacturer Name: OSD Displays

2. Part Number: T-51944D104J-FW-A-ABN

Manufacturer Name: OPTREX Corporation

3. Part Number: TLM-TA40T3130-01

Manufacturer Name: Varitronix

Figure 22: LVDS LCD Connector

Содержание iW-RainboW-G21D











































































































Результаты поиска

Содержание iW-RainboW-G21D

Отзывы:

Бренды по названию

Популярные бренды

iWave iW-RainboW-G21D, Руководство пользователя по оборудованию

Результаты поиска

Содержание iW-RainboW-G21D

Отзывы:

Бренды по названию

Популярные бренды