iWave iW-RainboW-G21D Скачать руководство пользователя страница 57

Страница: 57 / 106

REL1.0

Page 57 of 106

RZ/G1H Qseven Development Platform Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.8.2

”

LCD with Capacitive Touch

The RZ/G1H Qseven carrier board supports 7inch, 18bpp RGB

LCD “

ETM070001ADH6

” from

Emerging Display

Technologies Corporation (EDT) with capacitive touch panel. RZ/G1H

CPU’s

LVDS0 port is connected to primary LVDS

channel of Qseven MXM connector. This primary LVDS interface signals are directly connected to LVDS transmitter

(DS90CF384A) in carrier board which converts LVDS Interface signals to RGB and connects to RGB LCD connector (J8).

This RGB LCD connector (J8) is physically located at the top of board as shown below.

This RGB

LCD’s power enable and backlight enable is connected from

LVDS_PPEN (111

pin) & LVDS_BLEN (112

pin)

of Qseven MXM connector which is RZ/G1H CPU’s GPIO pins “

GP5_28

” and “

GP3_11

” respectively.

Also,

RGB LCD’s

brightness is controlled from LVDS_BLT_CTRL (123

pin)

of Qseven MXM connector which is RZ/G1H CPU’s

TPU0TO2(GP0_22).

Note In RZ/G1H carrier board, LVDS brightness control GPIO from Qseven MXM connector (123

Pin) is shared to both

primary & secondary LCD’s brightness control.

Figure 19: RGB LCD Connector

Содержание iW-RainboW-G21D











































































































Результаты поиска

Содержание iW-RainboW-G21D

Отзывы:

Бренды по названию

Популярные бренды

iWave iW-RainboW-G21D, Руководство пользователя по оборудованию

Результаты поиска

Содержание iW-RainboW-G21D

Отзывы:

Бренды по названию

Популярные бренды