Iveco NEF N40-ENT-M25 Скачать руководство пользователя страница 38

Страница: 38 / 70

installation directiVe

MAY 2006

N40 ENT M25

N60 ENT M37-M40

15. CUSTOMIZED INSTRUMENT PANEL

Using only the components of the panel that are not wired

to allow for panel customization, they will have to be wired

using the 10 meter long wire harness, set up at one end for

coupling to the JB connector and at the opposite end with

conductors with free terminals with identifying numbering

on each wire. The conductors will have to be connected to

the individual components as indicated in the electrical and

wiring diagrams in Chapter 24.

CAUTION

to assure the functionality of the safeties pertaining to the

engine start/stop commands from the instrument panel or

engine room, it is mandatory to wire the key switch strictly

as shown in the electrical diagrams in chapter 24.

The wiring details of the indications and alarms module

alone are provided below; indications for IVECO MOTORS

indicator instruments, are shown in the related wiring dia-

grams in Chapter 24.

JD Connector for indications and alarms module

VIEW FROM THE INTEGRATED SIDE

IN THE REAR PART OF THE MODULE

VIEW FROM THE TERMINAL SIDE

OF THE COUPLING SIDE WIRING

Connector TRIDENT - ITT Cannon

part # TST 24PA00

terminal

female

part # 192990-0050

lid

rear

part # TST24AH00

JD connects the indications and alarms module to the elec-

trical system of the engine (sensors, power supply, etc.).

The terminal part of the wire harness, supplied with the

module, must be completed using female terminals, as

described in the electrical diagram of Chapter 24.

For standard-equipped engines, to have the essential indica-

tions available, the following ways must be wired: 1, 2, 3, 7, 8,

9, 10, 13, 14, 15, 17, 18, 19 with the female terminals supplied

as standard equipment.

Figure 4

Figure 5

14 15 16

10 11 12

21 22 23 24

17 18 19 20

04_241_N

10 9

12 11

16 15

20 19

24 23

05_034_C

Содержание NEF N40-ENT-M25







































































Результаты поиска

Содержание NEF N40-ENT-M25

Отзывы:

Похожие инструкции для NEF N40-ENT-M25

Бренды по названию

Популярные бренды

Iveco NEF N40-ENT-M25, Руководство по установке

Результаты поиска

Содержание NEF N40-ENT-M25

Отзывы:

Похожие инструкции для NEF N40-ENT-M25

Бренды по названию

Популярные бренды