Iveco NEF N40-ENT-M25 Скачать руководство пользователя страница 24

Страница: 24 / 70

installation directiVe

N40 ENT M25

N60 ENT M37-M40

MAY 2006

9. MAIN ANALOG INSTRUMENT PANEL

Installation of the IVECO MOTORS onboard panel with

analog indicators entails connecting the panel’s JC connec-

tor to the JB connector on engine wire harness, interposing

the appropriate extension wire harness available in 3, 5 and

7 meter-long versions. The JC-JB wire harness comprises 47

lines, each connected to the terminal identified on both con-

nectors by the same number.

To the main panel is connected the JE connector, provided

for connection to the secondary panel; in installations with

no secondary panel, do not remove the cap of the JE con-

nector to avoid compromising the electrical continuity of the

systems’ power supply circuit.

Do not disconnect the connector 14 to avoid wrong fuel

filter clogging alarm indication.

1. Coolant temperature gauge (TA) - 2. Revolution counter and hour counter (CG) - 3.Voltmeter (V) - 4. Buzzer (SA) -

5. Indications and alarms module (MS) - 6. Engine oil pressure gauge (MO) - 7. Connector for secondary instrument panel (JE) -

8. On board panel instrument light switch (L) - 9. Engine start/stop key switch (CA) - 10. Engine stop push-button (usable only on

versions with excitation engine stop) - 11. Sound alarm inhibition push-button (P1) - 12. Connector for main panel wiring (JC) -

13. Cap with electrical continuity connection - 14. SIFC Alarm abilitation connector.

Figure 18

HOURS

electronic

RPMx100

bar

04_020_C

Содержание NEF N40-ENT-M25







































































Результаты поиска

Содержание NEF N40-ENT-M25

Отзывы:

Похожие инструкции для NEF N40-ENT-M25

Бренды по названию

Популярные бренды

Iveco NEF N40-ENT-M25, Руководство по установке

Результаты поиска

Содержание NEF N40-ENT-M25

Отзывы:

Похожие инструкции для NEF N40-ENT-M25

Бренды по названию

Популярные бренды