Iveco NEF N40-ENT-M25 Скачать руководство пользователя страница 39

Страница: 39 / 70

installation directiVe

N40 ENT M25

N60 ENT M37-M40

MAY 2006

CAUTION

to assure the utmost reliability and safety while underway, all installations must be provided with the following alarm indica-

tions:

(edc) edc failure

(sata) high coolant temperature

(sbpo) low oil pressure
it is also recommended that the following indications be present:

(sac) presence of water in the fuel pre-filter

(siFa) clogged air filter

(ss)

alternator fault

Functions of the JD terminals

pin description

electric level

oFF indication

on indication

Module power supply

Positive (+B)

EDC lamp power supply

Power supply positive (+B)

EDC Fault indication

High (+B)

Low (ground)

Pre-heating light power supply

Power supply positive (+B)

Pre-heating indication

High (+B)

Low (ground)

Pre-lubrication indication

Open circuit

High (+B)

Engine start

Power supply positive (+B) while starting

Sound alarm inhibition

Negative (ground) during the request

Module power supply

Negative (ground)

10 Buzzer power supply

Negative (ground) during the emission of sound

11 Clogged oil filter indication

Open circuit

Low (ground)

12 Clogged oil vapor filter indication

Open circuit

Low (ground)

13 Clogged air filter indication

Open circuit

Low (ground)

14 Clogged fuel filter indication

Low (ground)

Open circuit

15 Alternator fault indication

High (+B)

Low (1 to 3 V)

16 Low engine coolant level indication

Open circuit

Low (ground)

17 High coolant temperature indication

Open circuit

Low (ground)

18 Low engine oil pressure indication

Open circuit

Low (ground)

19 Presence of water in fuel indication

Open circuit

Low (ground)

20 Overloaded or runaway engine indication

Open circuit

High (+B)

21 Not connected

22 Not connected

23 Reception of data from main panel

NMEA communication protocol (0 to 5 V)

24 Transmission of data to secondary panel

NMEA communication protocol (0 to 5 V)

Содержание NEF N40-ENT-M25







































































Результаты поиска

Содержание NEF N40-ENT-M25

Отзывы:

Похожие инструкции для NEF N40-ENT-M25

Бренды по названию

Популярные бренды

Iveco NEF N40-ENT-M25, Руководство по установке

Результаты поиска

Содержание NEF N40-ENT-M25

Отзывы:

Похожие инструкции для NEF N40-ENT-M25

Бренды по названию

Популярные бренды