Iveco NEF N40-ENT-M25 Скачать руководство пользователя страница 23

Страница: 23 / 70

installation directiVe

MAY 2006

N40 ENT M25

N60 ENT M37-M40

Throttle lever position sensor

After testing the working condition of the linkage, adjust the

run of the servo components (see Chapter 18).

With the throttle at idle setting, the potentiometer rod

has to be in the resting position.

With the throttle at the stop, the potentiometer rod has

to be in the position of maximum run out.

Water presence in the pre-filter sensor

1. Pre - filter - 2. Conductor to be connected

with the negative battery terminal.

CAUTION

in order to enable the proper working of the sensor to

detect water in the fuel, it is necessary that the pre-filter

support is connected electrically to the negative battery

terminal.

In the engine models which use parts with insulated poles

it is necessary to electrically insulate the pre-filter support

from the boat mass and then connect the support with the

negative battery terminal.

Figure 1b

05_018_V

Содержание NEF N40-ENT-M25







































































Результаты поиска

Содержание NEF N40-ENT-M25

Отзывы:

Похожие инструкции для NEF N40-ENT-M25

Бренды по названию

Популярные бренды

Iveco NEF N40-ENT-M25, Руководство по установке

Результаты поиска

Содержание NEF N40-ENT-M25

Отзывы:

Похожие инструкции для NEF N40-ENT-M25

Бренды по названию

Популярные бренды