IV Produkt ThermoCooler HP 100 Скачать руководство пользователя страница 14

Страница: 14 / 20

Page 14

Operation and Maintenance

ThermoCooler HP

DSTCH.191101.01.EN

Continuous product development may give rise to specification changes without notice.

4.2 Cooling status

Status information is read on the Climatix display.

Information

Value

Explanation

Cooling unit status

UnitOn Status of cooling unit

Heating

x% Heating requirement from Climatix coo-

ling regulator

Cooling

x% Cooling requirement from Climatix coo-

ling regulator

Freq. inv. output

x.x% Frequency to the compressor

Compr. no

Comp1

Compr. Sum alarm

Normal

Alarm management

> The alarm is displayed if there is a fault

with the inverter or compressor. In the
event of an alarm, see "6.2 Alarm infor-
mation for inverter and compressor" page
17.

****************************************
Compressor C1

On/Off Compressor operating mode

Suction gas temp C1

x.x°C Measured suction gas temp

Evaporation temp C1

x.x°C Calculated evaporating temp based on

low pressure

Low pressure C1

x.x bar Relative pressure from low pressure sen-

sor

Overheating C1

x.x K Measured superheating

High pressure C1

x.x bar Relative pressure from high pressure sen-

sor

Expansion valve 1

x.x% Expansion valve position

Condensation temp C

x.x°C

Hot gas temperature

x.x°C Temperature of output from compressor

Liquid line temperature

x.x°C Temperature downstream of condenser

Supercooling

x.x°C Measured supercooling

Содержание ThermoCooler HP 100





















Результаты поиска

Содержание ThermoCooler HP 100

Отзывы:

Похожие инструкции для ThermoCooler HP 100

Бренды по названию

Популярные бренды

IV Produkt ThermoCooler HP 100, Эксплуатация и обслуживание

Результаты поиска

Содержание ThermoCooler HP 100

Отзывы:

Похожие инструкции для ThermoCooler HP 100

Бренды по названию

Популярные бренды