background image

30

Integrated Technical Vision Ltd

http://www.itvsystems.com.ua

Limited Warranty

Limited Warranty

ITV Ltd. warrants that for a period of eighteen months from the date of purchase,
the product shall be free of defect in materials and workmanship under normal use
and that in fulfillment of any breach of such warranty, ITV   Ltd. shall, at its option,
repair or replace the defective equipment upon return of the equipment to its repair
depot. This warranty applies only to defects in parts and workmanship and not
damaged incurred in shipping or handing, or damaged due to causes beyond the
control of ITV Ltd. such as lightning, excessive voltage, mechanical shock, water
damage, or damage arising out of abuse, alteration or improper application of the
equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be lieu
of any and all other warranties, whether expressed or implied and of all other
obligations or liabilities on the part of ITV Ltd. This warranty contains the entire
warranty. ITV Ltd. neither assumes, nor authorizes any other person purporting to
act on its behalf to modify or to change this warranty, nor to assume for it any
warranty or liability concerning this product.
In no event shall ITV Ltd. be liable for any direct, indirect or consequential damages.
Loss of anticipated profits, loss of time or any other losses incurred by the buyer in
connection with the purchase, installation or operation or failure of this product.

Содержание DLK642Lite

































Отзывы: