ITT NEO-DYN 100T Скачать руководство пользователя страница 14

 

Enclosure 6N Temperature switches

Page 11

  

WARRANTY INFORMATION 

A. Warranty

ITT Industries (ITT) warrants that at the time of shipment, the products manufactured by 

ITT Neo-Dyn

®

 and sold hereunder, will be free from defects in material and 

workmanship and will conform to the specifications furnished or approved by ITT. 

B. Warranty Adjustment

If any defect within this warranty appears, the Buyer shall notify ITT immediately. 

ITT agrees to repair or furnish a replacement for, but not install, any product which, 

within one (1) year from the date of shipment by ITT shall, upon test and examination by 

ITT, prove defective within the above warranty. 

No product will be accepted for return or replacement without the written authorization 

of ITT. Upon such authorization, and in accordance with instructions by ITT, the product 

will be returned with shipping charges prepaid by the Buyer. Replacements made under 

this warranty will be shipped prepaid. 

C. Exclusion from Warranty

THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER 

EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY, OR FITNESS, OR 

OTHERWISE. 

Components manufactured by any supplier other than ITT shall bear only the warranty 

made by the manufacturer of that product, and ITT assumes no responsibility for the 

performance or reliability of the unit as a whole. 

In no event shall ITT be liable for indirect, incidental or consequential damages nor shall 

the liability of ITT arising in connection with any products sold hereunder (whether such 

liability arises from a claim based on contract, warranty, tort or otherwise) exceed the 

actual amount paid by Buyer to ITT for the products delivered hereunder. 

The warranty does not extend to any product manufactured by ITT, which has been 

subject to misuse, neglect, accident, improper installation, or to use in violation of 

instructions furnished by ITT. 

The warranty does not extend to or apply to any unit, which has been repaired or altered 

at any place other than at ITT’s factory or service locations, by persons not expressly 

approved by ITT. 

Содержание NEO-DYN 100T















Отзывы: