ITT Goulds Pumps ICB Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 72

background image

2 Safety Regulations

2.1 Explosion Protection

On application of units in areas endangered to explosion measures and references in the

Filling of Unit

and

Maintenance

sections, must be observed, so that explosion protection is guaranteed.

Filling of unit

During operation of the pump the system of the suction and pressure pipe and the pump itself must

permanently be filled with the pumped liquid.

Thus, no explosive atmosphere can develop and the danger of dry-run is avoided.

If the operator can´t guarantee that, according monitoring measures must be provided.

NOTICE:

Equally all seal casings, auxiliary systems of the shaft sealing, as well as heating and cooling
systems must be filled carefully.

Marking

The marking of the pump refers to the pump itself. For the motor resp. further additions a separate

Declaration of Conformity, as well as a corresponding marking must be available.

Example of marking at pump: CE Ex II 2 G c T1-T.

The marking shows the theoretically applicable range of temperature classes. The different tempera-
tures, permitted acc. to pump design, result as shown in

Temperature Limits

. The same is valid for the

drive.

For a whole unit (pump, motor) with different temperature classes the lowest is valid.

Rotation Control

If danger of explosion is also existing during installation, the rotation control must not be carried out

by short start-up of the empty pump, to avoid undue temperature increase in case of contact of rotating
and stationary parts.

Operation of pump

The pump must only be started up with fully opened suction side and slightly opened pressure side
valve. The start-up against closed non-return valve, however, is possible. Immediately after the start-up
the discharge side valve must be adjusted to the operating point.

Refer to

6.1.4 Switch on drive on page 29

, as well.

Operation with closed valve in suction and / or discharge pipe is not permitted!

There´s a danger, that high surface temperatures are developing at the pump casing after relatively

short time, through fast heating of the liquid inside the pump.

NOTICE:

Fast pressure increase inside the pump can lead to overload and, thus, the pump can burst.

2 Safety Regulations

10

ICB Installation, Operation and Maintenance Instruction

«
...
10
11
12
13
14
...
»

Содержание Goulds Pumps ICB









































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICB

Бренд: Danfoss Страницы: 26

Бренд: Calpeda Страницы: 80

Бренд: Danfoss Страницы: 24

Бренд: GALAXY SPAS Страницы: 26

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: Danfoss Страницы: 22

Бренд: SMC Networks Страницы: 19

Бренд: Carrier Страницы: 12

Бренд: Bard Страницы: 49

Бренд: Grundfos Страницы: 160

Smartmax Series

Бренд: ubbink Страницы: 29

Бренд: Lampoassa Страницы: 62

Blue Diamond MaxiBlue

Бренд: Charles Austen Страницы: 20

Бренд: IMO Страницы: 11

Бренд: Heat-Flo Страницы: 20

Бренд: SFA Страницы: 80

Бренд: hajdu Страницы: 65

VariAir VASF 2.50/X-1.AC115

Бренд: Becker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды